Yamaha MD4S Owner's Manual - Page 32

32 Basic operation Mixdown When you have finished recording the four tracks, let's mixdown the recorded tracks to stereo, and record the mix on a master recorder. 1 R R R 4 2 POWER ON/ OFF 1 2 L L L 3 1 THRU OUT IN AC IN AUX SEND OUT OUT 2TR IN TRACK DIRECT OUT MIDI MONITOR STEREO IN OUT THRU MIDI TRACK DIRECT OUT 2TR IN STEREO MONITOR OUT OUT 1 2 AUX SEND 1 2 INSERT I/O MIC/LINE INPUT INSERT I/O 3 4 LINE INPUT 5 6 7 8 2 6 1 GAIN 2 GAIN 3 GAIN 4 GAIN 5/6 7/8 LINE MIC MIC/ LINE PB CUE FLIP P A N L R 0 HIGH L E V E L 10 LINE MIC MIC/ LINE PB CUE FLIP P A N L R 0 HIGH L E V E L 10 LINE MIC MIC/ LINE PB CUE FLIP P A N L R 0 HIGH L E V E L 10 LINE MIC MIC/ LINE PB CUE FLIP P A N L R 0 HIGH L E V E L 10 0 10 0 10 CUE MIX TO STEREO MONITOR SELECT 2TR IN -15 +15 -15 +15 -15 +15 -15 +15 MID MID MID MID -15 +15 -15 +15 -15 +15 -15 +15 LOW LOW LOW LOW -15 +15 -15 +15 -15 +15 -15 +15 AUX AUX AUX AUX STEREO CUE BUS MULTITRACK MD RECORDER 1 2 1 2 1 2 1 2 PAN PAN PAN PAN L R L R L R L R 10 10 10 10 9 9 9 9 8 8 8 8 7 7 7 7 6 6 6 6 5 5 5 5 4 4 4 4 3 3 3 3 2 2 2 2 1 1 1 1 0 0 0 0 MONITOR LEVEL MIN 10 9 8 7 6 5 4 3 2 1 0 MAX 10 9 8 7 6 5 4 3 2 1 0 1 2 3 4 STEREO REPEAT MARK SEARCH AB AUTO PUNCH I/O LAST REC SEARCH IN OUT SONG SEARCH REHE REC PLAY MARK SET PAUSE STOP TOC WRITE CH1 1 L REC SELECT CH2 CH3 2 3 R L CH4 4 R EJECT PEAK HOLD DISPLAY PITCH ADJUST EDIT UTILITY EXIT ENTER DATA CURSOR PHONES PUNCH I/O 4 58 7 9 3 s Connecting a master recorder 1 Connect the STEREO OUT jacks of the MD4S to the input jacks of your master recorder. Connect the output jacks of your master recorder to the 2TR IN jacks of the MD4S. s Adjust the mix balance of each track 2 Set the FLIP switches of input channels 1-4 to the "PB ( )" position. When the FLIP switches are set to the "PB ( )" position, the playback sound of the corresponding track will be sent to the input channel, allowing you to use the EQ controls to adjust the tone, and use the PAN control to set the stereo (left/right) position. The signals of input channels 1-4 (the track playback sound) will be mixed in stereo, and output via the ST bus to the STEREO OUT jacks. 3 Turn on the MONITOR SELECT STEREO switch. The ST bus will be selected as the signal source for monitoring. Now you can use headphones or monitor speakers connected to the PHONES jack or MONITOR OUT jacks to monitor the same signal as is being output from the STEREO OUT jacks. 4 Set the STEREO fader to the 7-8 mark. 5 Press the SONG SEARCH [ ] button to locate to the beginning of the song (the start point), and press the PLAY button to begin playback. -Owner's Manual