Yamaha MG206C Owner's Manual - Page 21

Reference Specifications MG206C ■ Electrical Specifications Frequency Response Total Harmonic Distortion (THD + N) Hum & Noise Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave attenuation. Crosstalk (1 kHz) Maximum voltage gain (1 kHz) All faders and controls are maximum when measured. PAN/BAL: panned hard left or hard right Phantom Voltage STEREO OUT GAIN: min (CHs 1-19/20) GROUP OUT 20 Hz-20 kHz AUX SEND Nominal output level @1 kHz Input: CHs 1 to 19/20, RETURN, 2TR IN MONITOR OUT, REC OUT STEREO OUT +14 dBu @ 20 Hz-20 kHz, Input GAIN Control at minimum MIN TYP MAX UNIT -3.0 0.0 1.0 dB 0.1 % CH INPUT 1-12 MIC EIN (Equivalent Input Noise): Rs = 150 Ω, GAIN: maximum STEREO OUT STEREO OUT, GROUP 1-2 fader and GROUP 3-4 fader at GROUP OUT nominal level and all channels' ST and 1-2, 3-4 switches off. AUX SEND Master/AUX control at nominal level and all CH AUX controls at minimum. STEREO OUT STEREO OUT, GROUP 1-2, GROUP 3-4 faders and one CH GROUP OUT fader at nominal level. STEREO OUT Residual Output Noise Adjacent Input CHs 1-12 Input to Output STEREO L/R, CHs 1-12, PAN: panned hard left or right Rs = 150 Ω MIC to CH INSERT OUT INPUT GAIN: maximum MIC to STEREO OUT MIC to GROUP OUT MIC to GROUP to ST MIC to REC OUT MIC to MONITOR OUT, ST TO MONITOR MIC to PHONES OUT MIC to AUX SEND PRE MIC to AUX SEND POST CH 17/18, 19/20 LINE to STEREO OUT CH 17/18, 19/20 LINE to GROUP OUT CH 17/18, 19/20 LINE to AUX SEND PRE CH 17/18, 19/20 LINE to AUX SEND POST Rs = 150 Ω RETURN to STEREO OUT RETURN to AUX SEND Rs = 600 Ω 2TR IN to STEREO OUT MIC no load -128 -88 -81 dBu -64 -98 -70 -70 dB 60 84 94 62.2 94 83 76 86 dB 58 47 57 16 9 27.8 48 V ■ General Specifications Input HPF Input equalization ±15 dB maximum Turn over/roll-off frequency of shelving: 3 dB blow maximum variable level. PEAK Indicator LED Level Meter Power Supply Adaptor Power Consumption Dimensions (W x H x D) Net Weight 80 Hz, 12 dB/oct CHs 1-12 HIGH: 10 kHz (shelving) MID: 250 Hz-5 kHz (peaking) LOW: 100 Hz (shelving) CH 13/14-19/20 HIGH: 10 kHz (shelving) MID: 2.5 kHz (peaking) LOW: 100 Hz (shelving) Red LED turns on when post EQ signal (either post MIC HA or post EQ signal for CHs 13/14-19/20) reaches -3 dB below clipping (+17 dBu). Pre MONITOR Level 2x12 points LED meter (PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB) STEREO/GROUP/PFL bus PEAK lights if the signal level reaches 3 dB below the clipping level. PA-30 AC 35 VCT, 1.4 A, Cable Length = 3.6 m 40 W 478 mm x 102 mm x 496 mm 6.0 kg All faders are nominal if not specified. Output impedance of signal generator: 150 ohms MG206C/MG166CX/MG166C Owner's Manual 75