Yamaha MG206C Owner's Manual - Page 23

Reference Specifications MG166CX/MG166C ■ Electrical Specifications Frequency Response Total Harmonic Distortion (THD + N) Hum & Noise Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave attenuation. Crosstalk (1 kHz) Maximum voltage gain (1 kHz) All faders and controls are maximum when measured. PAN/BAL: panned hard left or hard right Phantom Voltage STEREO OUT GAIN: min (CHs 1-11/12) GROUP OUT 20 Hz-20 kHz EFFECT/AUX* SEND Nominal output level @1 kHz Input: CHs 1 to 15/16, RETURN, 2TR IN MONITOR OUT, REC OUT STEREO OUT +14 dBu @ 20 Hz-20 kHz, Input GAIN Control at minimum CH INPUT 1-8 MIC EIN (Equivalent Input Noise): Rs = 150 Ω, GAIN: maximum STEREO OUT STEREO OUT, GROUP 1-2 fader and GROUP 3-4 fader at GROUP OUT nominal level and all channels' ST and 1-2, 3-4 switches off. EFFECT/AUX* SEND Master EFFECT/AUX* control at nominal level and all CH EFFECT/AUX* controls at minimum. STEREO OUT STEREO OUT, GROUP 1-2, GROUP 3-4 faders and one CH GROUP OUT fader at nominal level. STEREO OUT Residual Output Noise Adjacent Input CHs 1-8 Input to Output STEREO L/R, CHs 1-8, PAN: panned hard left or right Rs = 150 Ω MIC to CH INSERT OUT INPUT GAIN: maximum MIC to STEREO OUT MIC to GROUP OUT MIC to GROUP to ST MIC to REC OUT MIC to MONITOR OUT, ST TO MONITOR MIC to PHONES OUT MIC to AUX SEND PRE MIC to AUX SEND POST, EFFECT* SEND CH 9/10, 11/12 LINE to STEREO OUT CH 9/10, 11/12 LINE to GROUP OUT CH 9/10, 11/12 LINE to AUX SEND PRE CH 9/10, 11/12 LINE to AUX SEND POST, EFFECT* SEND CH 13/14, 15/16 to STEREO OUT CH 13/14, 15/16 to GROUP OUT Rs = 150 Ω RETURN to STEREO OUT RETURN to EFFECT/AUX* SEND Rs = 600 Ω 2TR IN to STEREO OUT MIC no load MIN TYP MAX UNIT -3.0 0.0 1.0 dB 0.1 % -128 -88 -81 dBu -64 -98 -70 -70 dB 60 84 94 62.2 94 83 76 86 dB 58 47 57 34 16 9 27.8 48 V ■ General Specifications Input HPF Input equalization ±15 dB maximum Turn over/roll-off frequency of shelving: 3 dB blow maximum variable level. PEAK Indicator Internal Digital Effect (Only MG166CX) LED Level Meter Power Supply Adaptor Power Consumption Dimensions (W x H x D) Net Weight CHs 1-11/12 80 Hz, 12 dB/oct CHs 1-8 HIGH: 10 kHz (shelving) MID: 250 Hz-5 kHz (peaking) LOW: 100 Hz (shelving) CH 9/10-15/16 HIGH: 10 kHz (shelving) MID: 2.5 kHz (peaking) LOW: 100 Hz (shelving) Red LED turns on when post EQ signal (either post MIC HA or post EQ signal for CHs 9/10-15/16) reaches -3 dB below clipping (+17 dBu). 16 PROGRAM, PARAMETER control Foot Switch (Digital Effect On/Off) Pre MONITOR Level 2x12 points LED meter (PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB) STEREO/GROUP/PFL bus PEAK lights if the signal level reaches 3 dB below the clipping level. PA-30 AC 35 VCT, 1.4 A, Cable Length = 3.6 m 35 W (MG166CX), 30 W (MG166C) 478 mm x 102 mm x 496 mm 5.5 kg (MG166CX), 5.3 kg (MG166C) All faders are nominal if not specified. Output impedance of signal generator: 150 ohms * MG166CX: AUX1, 2, EFFECT MG166C: AUX1, 2, 3 MG206C/MG166CX/MG166C Owner's Manual 77