Yamaha MW10 Owner's Manual - Page 23
Appendix, Specifications
View all Yamaha MW10 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 23 highlights
English Deutsch Appendix Appendix Specifications ■ Electrical Characteristics Total Harmonic Distortion (MIC to ST OUT) Frequency Response (CH INPUT 1-9/10, RETURN, 2TR IN to ST OUT, AUX SEND, C-R OUT, REC OUT) Hum & Noise Rs=150 ohms, Gain=Maximum (CH INPUT 1-2), Hum & Noise are measured with a -6 dB/octave filter @12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave attenuation. Maximum Voltage Gain 1 kHz, 10k ohms PAN/BAL: panned hard left or hard right. Crosstalk (1 kHz) Conditions (THD+N) 20 Hz - 20 kHz @ +14 dBu 10k ohms, GAIN controls at minimum level, all level controls at nominal level 20 Hz-20 kHz, nominal output level @ 1 kHz, 10 k ohms, GAIN controls at minimum level (CH INPUT 1-5/6), all level controls at nominal level Equivalent Input Noise (CH INPUT 1-2 MIC) Residual Output Noise (10 k ohms (ST OUT)) ST master control at nominal level and all channel LEVEL controls at minimum level. (ST OUT) All channel AUX controls at minimum level. (AUX SEND) ST master control and one channel LEVEL control at nominal level. (CH INPUT 1, 2) (ST OUT) CH INPUT 1, 2 MIC to CH INSERT OUT, Rs=150 ohms, GAIN controls at maximum level CH INPUT 1-5/6 MIC to ST OUT, Rs=150 ohms, GAIN controls at maximum level CH INPUT 1-5/6 MIC to REC OUT, Rs=150 ohms, GAIN controls at maximum level CH INPUT 1, 2 MIC to AUX SEND, Rs=150 ohms, GAIN controls at maximum level, PRE CH INPUT 1, 2 MIC to AUX SEND, Rs=150 ohms, GAIN controls at maximum level, POST CH INPUT 3/4-5/6 LINE to ST OUT, Rs=150 ohms, GAIN controls at maximum level CH INPUT 3/4-5/6 LINE to AUX SEND, Rs=150 ohms, GAIN controls at maximum level, PRE CH INPUT 3/4-5/6 LINE to AUX SEND, Rs=150 ohms, GAIN controls at maximum level, POST CH INPUT 7/8-9/10 to ST OUT, Rs=150 ohms, GAIN controls at maximum level RETURN to ST OUT, Rs=150 ohms 2TR IN to ST OUT, Rs=600 ohms Adjacent inputs input to output Where 0 dBu = 0.775 Vrms Output impedance of signal generator: 150 ohms MIN -3 TYP MAX 0.1 UNIT % 0 1 dB -128 dBu -100 dBu -87 (91 dB S/N) dBu -85 (89 dB S/N) dBu -64 (68 dB S/N) dBu 60 dB 76 dB 64.2 dB 70 dB 76 dB 50 dB 41 dB 47 dB 26 dB 12 dB 23.8 dB -70 dB -70 dB ■ General Specifications Monaural/Stereo CH High Pass Filter Monaural/Stereo CH Equalization Turn over/roll-off frequency of shelving, 3 dB below maximum variable level Phantom Power Monaural/Stereo Input PEAK Indicator USB Audio Included Accessories Power Consumption Dimensions (W × H × D) Net Weight Temperature Range 80 Hz 12 dB/octave ±15 dB (Max. Variation) HIGH: 10 kHz (shelving) MID: 2.5 kHz (peaking) LOW: 100 Hz (shelving) Supplied when Phantom +48 V switch is ON. (XLR-type input jacks) On each channel: red indicator lights if post-EQ signal (on stereo channels, if either post-EQ signal or post-mic-amp signal) comes within 3 dB of the clipping level. Input/Output: 44.1/48 kHz Power adaptor (PA-10), CD-ROM, USB cable, Owner's manual 19 W 251 mm × 65 mm × 290.5 mm 1.8 kg Operating temperature: 0 to 40 °C, Storage temperature: -20 to 60 °C Français Español MW10 Owner's Manual 23