Yamaha RX-V483 RX-V483 Owner s Manual - Page 32

Error messages

Get Yamaha RX-V483 PDF manuals and user guides View all Yamaha RX-V483 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Error messages If any error message is displayed during the measurement, resolve the problem and perform YPAO again. Error message TV screen LINK MASTER STEREO TUNED ZONE SLEEP PARTY 2 A 3 B OUT 2 Hi-Res ENHANCER YPAO VOL. A- DRC ECO E-5:NOISY VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Front display n Procedure to handle errors 1 Check the content of error message and press ENTER. 2 Use the cursor keys (e/r) to select the desired operation. To exit the YPAO measurement: 1 Select "EXIT" and press ENTER. 2 Use the cursor keys (q/w) to select "Exit" and press ENTER. 3 Disconnect the YPAO microphone from the unit. To retry the YPAO measurement from beginning: 1 Select "RETRY" and press ENTER. To proceed with the current YPAO measurement (for E-5 and E-9 only): 1 Select "PROCEED" and press ENTER. Error message E-1:No Front SP (E-1:NO FRNT SP) E-2:No Sur. SP (E-2:NO SUR SP) E-5:Noisy (E-5:NOISY) E-7:No MIC (E-7:NO MIC) E-8:No Signal (E-8:NO SIGNAL) E-9:User Cancel (E-9:CANCEL) E-10:Internal Err. (E-10:INTERNAL) Cause Remedy Front speakers are not detected. One of the surround speakers cannot be detected. Exit YPAO, turn off the unit, and then check the speaker connections. The noise is too loud. Keep the room quiet and retry YPAO. If you select "PROCEED", YPAO takes the measurement again and ignores any noise detected. The YPAO microphone has Connect the YPAO microphone to the been removed. YPAO MIC jack firmly and retry YPAO. The YPAO microphone cannot detect test tones. Connect the YPAO microphone to the YPAO MIC jack firmly and retry YPAO. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. The measurement has been canceled. Retry or exit YPAO as necessary. An internal error has occurred. Exit YPAO, and turn off and on the unit. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. Note Texts in parentheses denote indicators on the front display. 32 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
Error messages
If any error message is displayed during the measurement, resolve the problem and
perform YPAO again.
Error message
TV screen
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3B
2A
FPR
SBL
SB
SBR
FPL
MUTE VIRTUAL
E-5:NOISY
VOL.
SL
SW
SR
E-5:NOISY
Front display
n
Procedure to handle errors
1
Check the content of error message and press ENTER.
2
Use the cursor keys (
e
/
r
) to select the desired operation.
To exit the YPAO measurement:
1
Select “EXIT” and press ENTER.
2
Use the cursor keys (
q
/
w
) to select “Exit” and press ENTER.
3
Disconnect the YPAO microphone from the unit.
To retry the YPAO measurement from beginning:
1
Select “RETRY” and press ENTER.
To proceed with the current YPAO measurement (for E-5 and E-9
only):
1
Select “PROCEED” and press ENTER.
Error message
Cause
Remedy
E-1:No Front SP
(E-1:NO FRNT SP)
Front speakers are not
detected.
Exit YPAO, turn off the unit, and then
check the speaker connections.
E-2:No Sur. SP
(E-2:NO SUR SP)
One of the surround
speakers cannot be
detected.
E-5:Noisy
(E-5:NOISY)
The noise is too loud.
Keep the room quiet and retry YPAO. If
you select “PROCEED”, YPAO takes the
measurement again and ignores any
noise detected.
E-7:No MIC
(E-7:NO MIC)
The YPAO microphone has
been removed.
Connect the YPAO microphone to the
YPAO MIC jack firmly and retry YPAO.
E-8:No Signal
(E-8:NO SIGNAL)
The YPAO microphone
cannot detect test tones.
Connect the YPAO microphone to the
YPAO MIC jack firmly and retry YPAO. If
this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or
service center.
E-9:User Cancel
(E-9:CANCEL)
The measurement has been
canceled.
Retry or exit YPAO as necessary.
E-10:Internal Err.
(E-10:INTERNAL)
An internal error has
occurred.
Exit YPAO, and turn off and on the unit. If
this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or
service center.
Note
Texts in parentheses denote indicators on the front display.
En
32