Yamaha RX-V795 Owner's Manual - Page 26

To drive main, center and/or rear speakers with external amplifiers, MAIN terminals

Get Yamaha RX-V795 PDF manuals and user guides View all Yamaha RX-V795 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

PREPARATION Ⅵ To drive main, center and/or rear speakers with external amplifiers The speaker connections described on page 20 are fine for most applications. If for some reason, however, you wish to drive main, center and/or rear speakers with your existing amplifier, etc., the following terminals are available for connecting external amplifier(s) to this unit. OUTPUT MAIN CENTER REAR (SURROUND) SUB WOOFER 12 34 1 MAIN terminals These terminals are for main channel line output. If you drive main speakers with an external stereo power amplifier, connect the input terminals of the external amplifier (MAIN IN or AUX terminals of an amplifier or a receiver) to these terminals. There is no connection to these terminals when you use the built-in amplifier. * Output signals from the MAIN terminals are affected by the use of BASS, TREBLE, BALANCE controls, BASS EXTENSION button and the TONE BYPASS button. 2 SUBWOOFER terminal When using a subwoofer, connect its amplifier input to this terminal. Low frequencies distributed from the main, center and/or rear channels are output from this terminal. (The cut-off frequency of this terminal is 90 Hz.) Signals of LFE (low frequency effect) generated when Dolby Digital or DTS is decoded are also output if they are assigned to this terminal. 3 CENTER terminal This terminal is for center channel line output. If you drive a center speaker with an external power amplifier, connect the input terminal of the external amplifier to this terminal. There is no connection to this terminal when you use the built-in amplifier. 4 REAR (SURROUND) terminals These terminals are for rear channel line output. If you drive rear speakers with an external stereo power amplifier, connect the input terminals of the external amplifier (MAIN IN or AUX terminals of an amplifier or a receiver) to these terminals. There is no connection to these terminals when you use the built-in amplifier. Notes • Output level of signals from all of these terminals are adjusted by the use of VOLUME control on the front panel or VOLUME keys on the remote controller. • If an external power amplifier is connected to the MAIN, CENTER, or REAR output terminals, do not use the corresponding SPEAKERS terminals (MAIN, CENTER, or REAR). 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
22
The speaker connections described on page 20 are fine for
most applications. If for some reason, however, you wish to
drive main, center and/or rear speakers with your existing
amplifier, etc., the following terminals are available for
connecting external amplifier(s) to this unit.
1
MAIN terminals
These terminals are for main channel line output.
If you drive main speakers with an external stereo power
amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of an amplifier or a
receiver) to these terminals.
There is no connection to these terminals when you use
the built-in amplifier.
*
Output signals from the MAIN terminals are affected by
the use of
BASS
,
TREBLE
,
BALANCE
controls,
BASS
EXTENSION
button and the
TONE BYPASS
button.
2
SUBWOOFER terminal
When using a subwoofer, connect its amplifier input to
this terminal. Low frequencies distributed from the main,
center and/or rear channels are output from this terminal.
(The cut-off frequency of this terminal is 90 Hz.) Signals
of LFE (low frequency effect) generated when Dolby
Digital or DTS is decoded are also output if they are
assigned to this terminal.
3
CENTER terminal
This terminal is for center channel line output.
If you drive a center speaker with an external power
amplifier, connect the input terminal of the external
amplifier to this terminal.
There is no connection to this terminal when you use the
built-in amplifier.
4
REAR (SURROUND) terminals
These terminals are for rear channel line output.
If you drive rear speakers with an external stereo power
amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of an amplifier or a
receiver) to these terminals.
There is no connection to these terminals when you use
the built-in amplifier.
Notes
•
Output level of signals from all of these terminals are
adjusted by the use of
VOLUME
control on the front panel
or
VOLUME
keys on the remote controller.
•
If an external power amplifier is connected to the MAIN,
CENTER, or REAR output terminals, do not use the
corresponding SPEAKERS terminals (MAIN, CENTER, or
REAR).
m
To drive main, center and/or rear speakers with external amplifiers
MAIN
CENTER
REAR
(SURROUND)
OUTPUT
SUB
WOOFER
12
34
PREPARATION