Yamaha XDA-QS5400 XDA-QS5400 Owner s Manual - Page 13

Tab Basic Menu Settings Item Output Select AMP1 (2/3/4) BTL1 (2/3/4) AMP/BTL Trim Preout Trim Input Trim Auto Power Standby Network Standby Chime1 (2/3/4) Setting values Default Zone1 / Zone2 / Zone3 / Zone4 / None AMP1 - Zone1, AMP2 - Zone2, AMP3 - Zone3, AMP4 - Zone4 - - -10.0 to +10.0dB 0.0dB (0.5dB Steps) -10.0 to +10.0dB 0.0dB (0.5dB Steps) -6.0 to +6.0dB 0.0dB (0.5dB Steps) Off / 5 min / 20 min / 2 Hr / 4 Hr / 8 Hr / 12 Hr U.K. and Europe models : 20 min Other models : Off Off / On / Auto Auto Off / On Off Explanation Sets the zone as the audio output in each channel. Displays normal/bridge connection of speakers. Corrects volume difference between each channel and the standard output signal. Corrects volume difference between each preout signal in each Zone. Compensates for volume differences between input sources. Automatically sets the unit to standby mode when there are no operations for a specified amount of time. When this is set to 5 min or 20 min, the unit will only be set to standby mode automatically if there is no input signal during the 5 or 20 minutes without any operations. Enables/disables the feature allowing the Zone to be turned on by network devices (Network Standby). When this is "Auto", Network power will turn off when the main power is off and the unit continues not to be linked to network devices. Enables/disables the feature allowing the preset chime to sound in each Zone when the + and -of the CHIME 1 (/2/3/4) jack are shorted. Chime Volume Chime1 (2/3/4) Sound Chime1 (2/3/4) Test CUT IN CUT IN Power On Mute, -80.0 to 0.0dB (0.5dB Steps) (Sounds) - Off / On Disable / Enable - 30.0dB - - Off Disable Note If this function is enabled, the unit's standby power consumption increases to output audio immediately. Adjusts the chime volume in each Zone. Sets the preset chime for the CHIME 1 (/2/3/4). Tests the preset chime sound for the CHIME 1 (/2/3/4). Enables/disables the Cut in/Fade function in each Zone. Enables/disables the feature allowing the Zone to be turned on by the CUT IN input in each zone. CUT IN Mode Fade / Cut - 5sec / Cut - 10sec / Cut - 30sec / Cut - 1min / Cut - 5min Fade CUT IN Trim -30.0 to +30.0dB 0.0dB (0.5dB Steps) Note If all Zones are turned off (standby) and this function is enabled, the unit's power consumption increases to output audio immediately. Sets whether the audio signals from the CUT IN jacks fade in or cut in the playback. "Fade": mixes the audio signals from the CUT IN jacks into the lowered playback. The unit will be set to the previous playback automatically if there is no CUT IN signal for 3 seconds. "Cut": mutes the playback and outputs the audio signals from the CUT IN jacks instead. The unit will be set to the previous playback automatically if there is no CUT IN signal for 5 seconds to 5 minutes. Adjust the volume difference between the CUT IN input and the standard output signal. CUT IN Input Low / Mid / High Mid Sense Note If this is set to a high level, the sound may become clipped when the master volume level is high. It is recommended to set CUT IN Trim to a level at which there is no clipping at the desired master volume levels. Sets the sensitivity for audio input signal level of the CUT IN jacks. EN "Low": lowers the sensitivity and reacts to only loud sound. "High": heightens the sensitivity and reacts to even small sound. En 13