Yamaha YHT-22 Quick Connection Guide - Page 12

YHT-22 QUICK-CON N ECT GUIDE OPERATING THE RAV200 REMOTE CONTROL OVERVIEW The RAV200 remote control will control up to seven different types of components (including the HTR-5140 receiver), each of which becomes active when you press a selection (e.g., TV, VCR, etc.). We can only briefly describe some functions here, and we encourage you use the HTR-5140 Owner's Manual to gain additional experience with this powerful unit. PLAYING A VIDEOCASSETTE 1. Aim the remote control at the HTR-5140, press AMP/TUNER to select the component, and then press POWER to turn the receiver on. Press VCR (i.e., 6 on the keypad) as the input for the receiver. 2. Aim the remote control at the TV, press the TV to select the component, and then press POWER to turn the television on. Press TV INPUT (or A/B) to select the correct input. 3. Aim the remote control at the VCR, press VCR to select the component, and then press POWER to turn the VCR on. Put a tape in the VCR, press PLAY. NOTE: At this point, the VCR controls are assigned to the remote control, since VCR was the last selected component. If you now press the VOLUME up (down) buttons, the TV/VCR volume will be raised (or lowered). To adjust the receiver's volume, you must press AMP/TUNER to activate its functions. PLAYING A DVD 1. Aim the remote control at the HTR-5140, press AMP/ TUNER to select the component, and then press POWER to turn the receiver on. Press DVD/LD (i.e., 4 on the keypad) as the input for the receiver. NOTE: If the DVD player is connected to an external decoder, press EXT.DEC. (i.e., 9 on the keypad) as the input for the receiver. 2. Press DVD/LD and then press POWER to turn the DVD (or LD) player on. NOTE: If the DVD player is plugged into the switched ac outlet (on the back of the receiver) and its power switch was already engaged, the unit will come on each time the receiver is powered on. 3. Load a DVD (or LD) into the DVD (or LD) player. 4. Aim the remote control at the DVD (or LD) player, and press > (forward button) to start play. NOTE: The DVD player's controls are now assigned to the remote control buttons, since DVD was the last selected component. RESETTING THE RAV200 TO FACTORY CODES You can reset the RAV200 to factory codes for all components or a desired component, as follows: RESETTING CODES FOR ALL COMPONENTS 1. Press any component selector button other than AMP/TUNER. 2. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 3. Using the keypad, enter the code "9990". 4. The indicator LED will flash twice to confirm all codes have been reset to factory values. If the LED does not flash twice, repeat steps 1 through 3. RESETTING CODES FOR A DESIRED COMPONENT 1. Press a component selector button that matches the component you wish to reset to factory codes. 2. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 3. Using the keypad, enter the code "0000". 4. The indicator LED will flash twice to confirm all codes have been reset to factory values. If the LED does not flash twice, repeat steps 1 through 3. 5. For your convenience, the following reference chart lists the factory codes: Component Component Selector Button Code TV CBL/DBS VCR DVD/LD CD TAPE/MD TV DBS tuner VCR DVD player CD player Tape deck 0101 0006 0002 0008 Yamaha 0005 Yamaha 0004 Yamaha ©1999 YAMAHA ELECTRONICS CORPORATION, USA 6660 Orangethorpe Avenue, Buena Park, CA 90620 PH: (714) 522-9105; FAX: (800) 634-0355 http://www.yamaha.com 12