Yamaha YST-SW40 Owner's Manual - Page 10

Adjusting Volume, Frequency Characteristics - set of speakers

Get Yamaha YST-SW40 PDF manuals and user guides View all Yamaha YST-SW40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

ADJUSTING VOLUME POWER HIGH CUT VOLUME 50 Hz 150 Hz 0 10 2 5 1, 4 FREQUENCY CHARACTERISTICS Adjustment of the VOLUME control and the HIGH CUT control should be changed according to the main speakers, listening condition, source, etc. Following figures show the optimum adjustment of each control and the frequency characteristics when this unit is combined with a typical speaker system. 1 Set the VOLUME control to minimum. 2 Turn on the power supply to all the components. 3 Play any source and adjust the amplifier's volume control to the desired listening level. 4 Turn up the VOLUME control gradually to adjust the volume balance between this unit and the main speakers. 5 Adjust the HIGH CUT control to the position where the desired response can be obtained. Notes • Once the volume balance between this unit and the main speakers is adjusted, you can adjust the volume of your whole sound system by using only the amplifier's volume control. • For adjusting the VOLUME control and the HIGH CUT control, refer to "FREQUENCY CHARACTERISTICS" on the right hand. For effective adjustment of the HIGH CUT control First set this control at about the main speakers' rated minimum reproduceable frequency. Then turn up the VOLUME control gradually and set it at a level where you can obtain a little more bass effect than when this unit is not used. On the basis of this setting, if desired, adjust the VOLUME control and the HIGH CUT control again. * The main speakers' minimum reproduceable frequency can be looked up in the speakers' catalog or owner's manual. This unit's frequency characteristics dB HIGH CUT 100 Hz 90 HIGH CUT 150 Hz 80 70 60 HIGH CUT 50 Hz 50 40 20 50 100 200 500Hz • When combined with a 3" or 4" acoustic suspension, 2 way system dB 90 HIGH CUT VOLUME 80 70 YST-SW40 50 Hz 150 Hz 0 10 60 Main 50 speaker's response 40 20 50 100 200 500Hz • When combined with 5" acoustic suspension, 2 way system dB HIGH CUT VOLUME 50 Hz 150 Hz 0 10 90 80 YST-SW40 70 60 Main speaker's response 50 40 20 50 100 200 500Hz 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
10
1
Set the
VOLUME
control to minimum.
2
Turn on the power supply to all the components.
3
Play any source and adjust the amplifier’s volume control
to the desired listening level.
4
Turn up the
VOLUME
control gradually to adjust the
volume balance between this unit and the main speakers.
5
Adjust the
HIGH CUT
control to the position where the
desired response can be obtained.
Notes
•
Once the volume balance between this unit and the main
speakers is adjusted, you can adjust the volume of your
whole sound system by using only the amplifier’s volume
control.
•
For adjusting the
VOLUME
control and the
HIGH CUT
control, refer to “FREQUENCY CHARACTERISTICS” on
the right hand.
For effective adjustment of the HIGH CUT control
First set this control at about the main speakers’ rated
minimum reproduceable frequency.
Then turn up the
VOLUME
control gradually and set it at a level where you can
obtain a little more bass effect than when this unit is not used.
On the basis of this setting, if desired, adjust the
VOLUME
control and the
HIGH CUT
control again.
*
The main speakers’ minimum reproduceable frequency can
be looked up in the speakers’ catalog or owner’s manual.
FREQUENCY CHARACTERISTICS
Adjustment of the
VOLUME
control and the
HIGH CUT
control
should be changed according to the main speakers, listening
condition, source, etc.
Following figures show the optimum adjustment of each control
and the frequency characteristics when this unit is combined
with a typical speaker system.
This unit’s frequency characteristics
•
When combined with a 3” or 4” acoustic
suspension, 2 way system
•
When combined with 5” acoustic
suspension, 2 way system
ADJUSTING VOLUME
POWER
HIGH CUT
VOLUME
150 Hz
0
10
50 Hz
2
5
1, 4
20
50
100
200
500Hz
40
50
60
70
80
90
dB
HIGH CUT 50 Hz
HIGH CUT 100 Hz
HIGH CUT 150 Hz
VOLUME
0
10
HIGH CUT
150 Hz
50 Hz
VOLUME
0
10
HIGH CUT
150 Hz
50 Hz
20
50
100
200
500Hz
40
50
60
70
80
90
dB
YST-SW40
20
50
100
200
500Hz
40
50
60
70
80
90
dB
YST-SW40
Main
speaker’s
response
Main
speaker’s
response