Yamaha YST-SW45 Owner's Manual - Page 9

Controls And Their Functions - volume

Page 9 highlights

English CONTROLS AND THEIR FUNCTIONS Front panel STANDBY/ON HIGH CUT VOLUME 40 Hz 140 Hz 0 10 STANDBY/ON HIGH CUT VOLUME Rear panel POWER ON OFF @ 50 Hz 150 Hz 0 10 ~Ÿ ! ⁄ OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY FROM AMPLIFIER INPUT1 LOW HIGH OFF OUTPUT TO SPEAKERS POWER ON OFF FROM AMPLIFIER INPUT1 INPUT2 AUTO STANDBY LOW HIGH OFF ¤ ~ Power indicator Lights up while this unit is ON. * If the AUTO STANDBY switch on the rear panel is set to the LOW or HIGH position, this indicator is illuminated dimly when no signal is input to this unit. Ÿ STANDBY/ON button Each press of this button turns the unit on and off (on standby). A small amount of power is always consumed even while this unit is on standby. ! HIGH CUT control Adjusts the high frequency cut off point. Frequencies higher than the frequency selected with this control are all cut off (and not output). ⁄ VOLUME control Adjusts the volume level. @ Main POWER switch Normally, leave this switch to the ON position. When you will not use this unit for a long period, set this switch to the OFF position. ¤ AUTO STANDBY switch With this switch, you can activate the Automatic Standby function. Normally, set the switch to the LOW position. To cancel this function, set the switch to the OFF position. * Change the setting of this switch only when the power of this unit is on standby (by setting the STANDBY/ON button to OFF). Automatic Standby function When you play a source, the power of this unit turns on automatically by sensing audio signals input to this unit. This unit turns into the standby mode automatically if the source being played is stopped or the low frequency input signal is cut off for several minutes. This function will operate by sensing a certain level of low frequency input signal. Its sensitivity is high in the HIGH position and low in the LOW position of the AUTO STANDBY switch. In the HIGH position, the power will turn on even with a low level of input signal, but on the other hand this unit may not turn into the standby mode when there is an input signal even if its level is extremely low. * There may be a case that the power turns on unexpectedly by sensing noise from other appliances. If it occurs, set the AUTO STANDBY switch to the OFF or LOW position. * The level of low frequency input signal differs with each source, and each different part on the same source. So, this function may not operate properly depending on some sources. This function is available only when the power of this unit is on (by setting the STANDBY/ON button Ÿ to ON). 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14

9
English
POWER
ON
OFF
OUTPUT
INPUT2
TO SPEAKERS
INPUT1
FROM AMPLIFIER
LOW
HIGH
OFF
AUTO
STANDBY
POWER
150 Hz
0
10
50 Hz
STANDBY/ON
HIGH CUT
VOLUME
Front panel
Rear panel
CONTROLS AND THEIR FUNCTIONS
Automatic Standby function
When you play a source, the power of this unit turns on
automatically by sensing audio signals input to this unit. This
unit turns into the standby mode automatically if the source
being played is stopped or the low frequency input signal is
cut off for several minutes.
This function will operate by sensing a certain level of low
frequency input signal. Its sensitivity is high in the HIGH
position and low in the LOW position of the
AUTO STANDBY
switch. In the HIGH position, the power will turn on even with
a low level of input signal, but on the other hand this unit may
not turn into the standby mode when there is an input signal
even if its level is extremely low.
*
There may be a case that the power turns on unexpectedly
by sensing noise from other appliances. If it occurs, set the
AUTO STANDBY
switch to the OFF or LOW position.
*
The level of low frequency input signal differs with each
source, and each different part on the same source. So,
this function may not operate properly depending on some
sources.
This function is available only when the power of this
unit is on (by setting the STANDBY/ON button
Ÿ
to ON).
~
Power
indicator
Lights up while this unit is ON.
*
If the
AUTO STANDBY
switch on the rear panel is set
to the LOW or HIGH position, this indicator is illumi-
nated dimly when no signal is input to this unit.
Ÿ
STANDBY/ON
button
Each press of this button turns the unit on and off (on
standby). A small amount of power is always consumed
even while this unit is on standby.
!
HIGH CUT
control
Adjusts the high frequency cut off point.
Frequencies higher than the frequency selected with this
control are all cut off (and not output).
VOLUME
control
Adjusts the volume level.
@
Main POWER
switch
Normally, leave this switch to the ON position. When you
will not use this unit for a long period, set this switch to the
OFF position.
¤
AUTO STANDBY
switch
With this switch, you can activate the Automatic Standby
function. Normally, set the switch to the LOW position.
To cancel this function, set the switch to the OFF position.
*
Change the setting of this switch only when the power of
this unit is on standby (by setting the
STANDBY/ON
button to OFF).
¤
@
!
~
Ÿ