Zanussi Z716WT83BI User Manual - Page 18

Dial And Buttons - reset

Page 18 highlights

DIAL AND BUTTONS INTRODUCTION The options/functions are not available with all washing programmes. Check the compatibility between options/ functions and washing programmes in the "Programme Chart". An option/ function can exclude another one, in this case the appliance doesn't allow you to set incompatible options/ functions. ON/OFF Press this button for a few seconds to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off. As the Stand-by function automatically deactivates the appliance after several minutes to reduce the energy consumption, you may need to activate the appliance again. For more details, refer to Stand-by paragraph in Daily Use chapter. MODE Thanks to this button, a cycle can perform: • Only washing: Mode - Wash indicator is on (default mode). • Washing and drying: Mode - Wash and Mode - Dry indicators are on. • Only drying: Mode - Dry indicator is on. TEMP. When you select a washing programme, the appliance automatically proposes a default temperature. Tap on this button to change the water temperature. The indicator of the set temperature comes on. The indicator Cold corresponds to cold water. SPIN When you set a programme, the appliance automatically sets the maximum spin speed allowed, except for programme Denim. With this option you can decrease the default spin speed. Touch repeatedly this button to: • Decrease the spin speed. The display shows only the spin speeds available for the set programme. • Additional spin options No Spin . Set this option to deactivate all spin phases. The appliance performs the only draining phase of the selected washing programme. Set this option for very delicate fabrics. The rinses phase uses more water for some washing programmes • Activate the Rinse Hold option. The final spin is not performed. The water of the last rinse is not drained out to prevent the fabrics from creasing. The washing programme ends with water in the drum. The indicator is on display. The door stays locked and the drum turns regularly to reduce creasing. You must drain the water to unlock the door. If you touch the Start/Pause button, the appliance performs the spinning phase and drains the water. The appliance empties the water out automatically after 18 hours approximately. PREWASH With this option you can add a prewash phase to a washing programme. The corresponding indicator above the touch button illuminates. • Use this option to add a pre-wash phase at 30 °C before the washing phase. This option is recommended for heavily soiled laundry, especially if containing sand, dust, mud and other solid particles. The options can increase the programme duration. PERMANENT EXTRA RINSE With this option you can permanently have an extra rinse when you set a new programme. To activate/deactivate this option, hold the Prewash button pressed for 3 seconds until the indicator comes on/goes off on the display. When it is activated, the appliance will default to this option after you switch it off or change/reset the programme. This option increases the programme duration. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

DIAL AND BUTTONS
INTRODUCTION
The options/functions are not available
with all washing programmes. Check
the compatibility between options/
functions and washing programmes in
the "Programme Chart". An option/
function can exclude another one, in
this case the appliance doesn't allow
you to set incompatible options/
functions.
ON/OFF
Press this button for a few seconds to activate or
deactivate the appliance. Two different tunes sound
while switching the appliance on or off.
As the Stand-by function automatically deactivates
the appliance after several minutes to reduce the
energy consumption, you may need to activate the
appliance again.
For more details, refer to Stand-by paragraph in
Daily Use chapter.
MODE
Thanks to this button, a cycle can perform:
Only washing
: Mode - Wash indicator is on
(default mode).
Washing and drying
: Mode - Wash and Mode
- Dry indicators are on.
Only drying
: Mode - Dry indicator is on.
TEMP.
When you select a washing programme, the
appliance automatically proposes a default
temperature.
Tap on this button to change the water
temperature.
The indicator of the set temperature comes on.
The indicator Cold corresponds to cold water.
SPIN
When you set a programme, the appliance
automatically sets the maximum spin speed
allowed, except for programme Denim. With this
option you can decrease the default spin speed.
Touch repeatedly this button to:
Decrease the spin speed.
The display shows
only the spin speeds available for the set
programme.
Additional spin options
No Spin
.
Set this option to deactivate all spin phases.
The appliance performs the only draining phase
of the selected washing programme. Set this
option for very delicate fabrics. The rinses phase
uses more water for some washing programmes
Activate the
Rinse Hold
option.
The final spin is not performed. The water of the
last rinse is not drained out to prevent the
fabrics from creasing. The washing programme
ends with water in the drum.
The indicator
is on display. The door stays
locked and the drum turns regularly to reduce
creasing. You must drain the water to unlock the
door.
If you touch the Start/Pause
button, the
appliance performs the spinning phase and
drains the water.
The appliance empties the water
out automatically after 18 hours
approximately.
PREWASH
With this option you can add a prewash phase to a
washing programme.
The corresponding indicator above the touch
button illuminates.
Use this option to add a pre-wash phase at 30
°C before the washing phase.
This option is recommended for heavily soiled
laundry, especially if containing sand, dust, mud
and other solid particles.
The options can increase the
programme duration.
PERMANENT EXTRA RINSE
With this option you can permanently have an extra
rinse when you set a new programme.
To
activate/deactivate
this option, hold the
Prewash button pressed for 3 seconds until the
indicator
comes on/goes off
on the display.
When it is activated, the appliance will default to
this option after you switch it off or change/reset
the programme.
This option increases the programme
duration.
18