Zanussi ZIT6470CB User Manual - Page 12

Installation

Get Zanussi ZIT6470CB PDF manuals and user guides View all Zanussi ZIT6470CB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Problem Possible cause Remedy comes on. comes on. and a number come on. You can hear a constant beep noise. Child Safety Device or Lock operates. There is no cookware on the zone. The cookware is unsuitable. The diameter of the bottom of the cookware is too small for the zone. There is an error in the hob. The electrical connection is incorrect. Refer to "Daily use". Put cookware on the zone. Use suitable cookware. Refer to "Hints and tips". Use cookware with correct dimensions. Refer to "Technical data". Deactivate the hob and activate it again after 30 seconds. If comes on again, disconnect the hob from the electrical supply. After 30 seconds, connect the hob again. If the problem continues, speak to an Authorised Service Centre. Disconnect the hob from the electrical supply. Ask a qualified electrician to check the installation. IF YOU CANNOT FIND A SOLUTION... If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre. Give the data from the rating plate. Give also three digit letter code for the glass ceramic (it is in the corner of the glass surface) and an error message that comes on. Make sure, you operated INSTALLATION the hob correctly. If not the servicing by a service technician or dealer will not be free of charge, also during the warranty period. The instructions about the Service Centre and conditions of guarantee are in the guarantee booklet. WARNING! Refer to Safety chapters. BEFORE THE INSTALLATION Before you install the hob, write down the information bellow from the rating plate. The rating plate is on the bottom of the hob. Serial number BUILT-IN HOBS Only use the built-in hobs after you assemble the hob into correct built-in units and work surfaces that align to the standards. CONNECTION CABLE • For a single phase or two phase connection, use the cable type: H05BB-F or H03V2V2-F which withstands a temperature of 70°C or higher. • To replace the damaged mains cable, use the cable: H05BB-F or H03V2V2-F which withstands a temperature of 70°C or higher. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
Problem
Possible cause
Remedy
comes on.
Child Safety Device or Lock
operates.
Refer to "Daily use".
comes on.
There is no cookware on the
zone.
Put cookware on the zone.
The cookware is unsuitable.
Use suitable cookware. Refer
to "Hints and tips".
The diameter of the bottom of
the cookware is too small for
the zone.
Use cookware with correct di-
mensions. Refer to "Technical
data".
and a number come on.
There is an error in the hob.
Deactivate the hob and acti-
vate it again after 30 seconds.
If
comes on again, discon-
nect the hob from the electrical
supply. After 30 seconds, con-
nect the hob again. If the prob-
lem continues, speak to an Au-
thorised Service Centre.
You can hear a constant beep
noise.
The electrical connection is in-
correct.
Disconnect the hob from the
electrical supply. Ask a quali-
fied electrician to check the in-
stallation.
IF YOU CANNOT FIND A SOLUTION...
If you cannot find a solution to the problem yourself,
contact your dealer or an Authorised Service
Centre. Give the data from the rating plate. Give
also three digit letter code for the glass ceramic (it
is in the corner of the glass surface) and an error
message that comes on. Make sure, you operated
the hob correctly. If not the servicing by a service
technician or dealer will not be free of charge, also
during the warranty period. The instructions about
the Service Centre and conditions of guarantee are
in the guarantee booklet.
INSTALLATION
WARNING!
Refer to Safety chapters.
BEFORE THE INSTALLATION
Before you install the hob, write down the
information bellow from the rating plate. The rating
plate is on the bottom of the hob.
Serial number
...........................
BUILT-IN HOBS
Only use the built-in hobs after you assemble the
hob into correct built-in units and work surfaces
that align to the standards.
CONNECTION CABLE
•
For a single phase or two phase connection,
use the cable type: H05BB-F or H03V2V2-F
which withstands a temperature of 70°C or
higher.
•
To replace the damaged mains cable, use the
cable: H05BB-F or H03V2V2-F which
withstands a temperature of 70°C or higher.
12