Zanussi ZWF01280W User Manual - Page 15

Troubleshooting

Get Zanussi ZWF01280W PDF manuals and user guides View all Zanussi ZWF01280W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

CLEANING THE INLET HOSE AND THE VALVE FILTER 1. 1 2 3 2. FROST PRECAUTIONS If the appliance is installed in an area where the temperature can be less than 0 °C, remove the remaining water from the inlet hose and the drain pump. Do this procedure also when you want to do the emergency drain. 1. Disconnect the mains plug from the mains socket. 2. Remove the water inlet hose. 3. Remove the drain hose from the rear support and unhook it from sink or spigot. 4. Put the ends of the drain and inlet hose in a container. Let the water flow out of the hoses. 5. Set any selected programme with option Drain & Spin and let it operate until the end of the cycle. 6. When no more water flows, install the inlet hose and the drain hose again. 7. Press the On/Off button to deactivate the appliance. WARNING! Make sure that the temperature is more than 0°C before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures. 3. 45° 20° 4. TROUBLESHOOTING WARNING! Refer to Safety chapters. INTRODUCTION The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the Authorised Service Centre. With some problems, the acoustic signals operate. The indicator of button flashes in red and one of the indicators comes on, to show an alarm code: • - The appliance does not fill with water properly. • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. Please check the door! 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
CLEANING THE INLET HOSE AND THE VALVE
FILTER
1.
1
2
3
2.
3.
4.
45°
20°
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0 °C, remove the
remaining water from the inlet hose and the drain
pump.
Do this procedure also when you want
to do the emergency drain.
1.
Disconnect the mains plug from the mains
socket.
2.
Remove the water inlet hose.
3.
Remove the drain hose from the rear support
and unhook it from sink or spigot.
4.
Put the ends of the drain and inlet hose in a
container. Let the water flow out of the hoses.
5.
Set any selected programme with option Drain
& Spin and let it operate until the end of the
cycle.
6.
When no more water flows, install the inlet
hose and the drain hose again.
7.
Press the On/Off button to deactivate the
appliance.
WARNING!
Make sure that the
temperature is more than 0°C before
you use the appliance again. The
manufacturer is not responsible for
damages caused by low temperatures.
TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
INTRODUCTION
The start of the appliance does not occur or it
stops during operation.
First try to find a solution to the problem (refer to
the table). If not, contact the Authorised Service
Centre.
With some problems, the acoustic signals operate.
The indicator of button
flashes in
red
and one
of the indicators comes on, to show an alarm code:
•
- The appliance does not fill with water
properly.
•
- The appliance does not drain the water.
•
- The appliance door is open or not closed
correctly. Please check the door!
15