ZyXEL P-330W User Guide - Page 27

Navigating the P-330W Web Configurator, Navigation Panel - firmware upgrade

Page 27 highlights

ZyXEL P-330W User's Guide 2.2.0.1.1 Procedure To Use The Reset Button 1 Make sure the PWR LED is on (not blinking). 2 Press the RESET button for approximately ten seconds or until the PWR LED begins to blink and then release it. When the PWR LED begins to blink, the defaults have been restored and the P-330W restarts. (If you press the RESET button for less than 5 seconds, the P-330W will reboot, but will not reset the configuration). 2.2.1 Navigating the P-330W Web Configurator The following summarizes how to navigate the web configurator from the SITE MAP screen. • Click SETUP WIZARD for initial configuration including general setup, Wireless LAN Setup, ISP parameters for Internet Access and WAN IP/DNS Server/MAC address assignment. • Click a link under WIRELESS to configure wireless settings. • Click a link under ADVANCED to configure advanced P-330W features. • Click LOGOUT at any time to exit the web configurator. • Click ADMINISTRATOR to view information about your P-330W or upgrade configuration/firmware files. Administrator includes Statistics, Remote Management, Upgrade Firmware, Config File (Backup, Restore, Defaults) and Time Zone Settings. Figure 3 The MAIN MENU Screen of the Web Configurator 2.2.2 Navigation Panel After you log in, use the sub-menus on the navigation panel to configure P-330W features. 27 Chapter 2 Introducing the Web Configurator

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141

ZyXEL P-330W User’s Guide
27
Chapter 2 Introducing the Web Configurator
2.2.0.1.1
Procedure To Use The Reset Button
1
Make sure the
PWR
LED is on (not blinking).
2
Press the
RESET
button for approximately ten seconds or until the
PWR
LED begins to
blink and then release it. When the
PWR
LED begins to blink, the defaults have been
restored and the P-330W restarts. (If you press the
RESET
button for less than 5 seconds,
the P-330W will reboot, but will not reset the configuration).
2.2.1
Navigating the P-330W Web Configurator
The following summarizes how to navigate the web configurator from the
SITE MAP
screen.
• Click
SETUP
WIZARD
for initial configuration including general setup,
Wireless LAN
Setup
, ISP parameters for Internet Access and WAN IP/DNS Server/MAC address
assignment.
Click a link under
WIRELESS
to configure wireless settings.
Click a link under
ADVANCED
to configure advanced P-330W features.
• Click
LOGOUT
at any time to exit the web configurator.
• Click
ADMINISTRATOR
to view information about your P-330W or upgrade
configuration/firmware files. Administrator includes
Statistics
,
Remote Management
,
Upgrade Firmware
,
Config File
(Backup, Restore, Defaults) and
Time Zone Settings
.
Figure 3
The MAIN MENU Screen of the Web Configurator
2.2.2
Navigation Panel
After you log in, use the sub-menus on the navigation panel to configure P-330W features.