3Com 2848 SFP User Guide - Page 37

Configuring Trunking, Guidelines for creating Trunks, Defining the Members of a Trunk

Get 3Com 2848 SFP - Baseline Switch Plus PDF manuals and user guides
UPC - 662705502243
View all 3Com 2848 SFP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

To set up the configuration shown in Figure 15, do the following: 1 Use the Create VLANs screen (Figure 13) to create VLAN2 on both Switch 1 and Switch 2. (VLAN1 is the default VLAN and already exists.) 2 For Switch 1, click the icon under port numbers you want to add to VLAN2 until you see the letter U for Untagged. Select T or Tagged as the mode for port 16. 3 Click Apply. 4 For Switch 2, click the icon under port numbers you want to add to VLAN2 until you see the letter U for Untagged. Select T or Tagged as the mode for port 8. 5 Click Apply. 6 Connect port 16 on Switch 1 to port 8 on Switch 2. Those ports on Switch 1 that are members of VLAN2 can now communicate with those ports on Switch 2 that are members of VLAN2. Configuring Trunking Ports can be statically grouped into a trunk, also known as an aggregated link under the IEEE 802.1ad standard. This increases the bandwidth of a network connection and ensures fault recovery. Trunking permits the connection of multiple ports to the same remote device to achieve higher network throughput. For link aggregation to work, the trunks must be configured on both ends of the switches. Configuring Trunking 37 The Switch does not support the Link Aggregation Control Protocol (LACP), which is specified in IEEE 802.3ad. Guidelines for creating Trunks ■ Any of the ports on the Switch can be used for creating a trunk. ■ This Switch can support a maximum of 4 trunks. ■ Each trunk may contain up to 8 members. ■ A port may only be a member of one trunk at any one time. All ports in a trunk must be configured in an identical manner, including communication modes such as speed, duplex mode and flow control. Defining the Members of a Trunk Use the Membership/Setup tab of the Link Aggregation page to specify the members of a trunk. To define the members of a trunk: 1 On the Membership/Setup tab, select the same trunk number under Group Membership for the ports that you want to trunk. For example, if you want ports 2, 3, 4, and 5 to become members of Trunk 2, set the Group Membership for these ports to 2. 2 Click Apply.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Configuring Trunking
37
To set up the configuration shown in Figure 15, do the
following:
1
Use the Create VLANs screen (Figure 13) to create
VLAN2 on both Switch 1 and Switch 2. (VLAN1 is the
default VLAN and already exists.)
2
For Switch 1, click the icon under port numbers you
want to add to VLAN2 until you see the letter
U
for
Untagged
. Select
T or Tagged
as the mode for port 16.
3
Click
Apply
.
4
For Switch 2, click the icon under port numbers you
want to add to VLAN2 until you see the letter
U
for
Untagged
. Select
T or Tagged
as the mode for port 8.
5
Click
Apply
.
6
Connect port 16 on Switch 1 to port 8 on Switch 2.
Those ports on Switch 1 that are members of VLAN2
can now communicate with those ports on Switch 2
that are members of VLAN2.
Configuring Trunking
Ports can be statically grouped into a trunk, also known
as an aggregated link under the IEEE 802.1ad standard.
This increases the bandwidth of a network connection
and ensures fault recovery. Trunking permits the
connection of multiple ports to the same remote device
to achieve higher network throughput.
For link aggregation to work, the trunks must be
configured on both ends of the switches.
The Switch does not support the Link Aggregation
Control Protocol (LACP), which is specified in IEEE
802.3ad.
Guidelines for creating Trunks
■
Any of the ports on the Switch can be used for
creating a trunk.
■
This Switch can support a maximum of 4 trunks.
■
Each trunk may contain up to 8 members.
■
A port may only be a member of one trunk at any
one time.
All ports in a trunk must be configured in an identical
manner, including communication modes such as speed,
duplex mode and flow control.
Defining the Members of a Trunk
Use the
Membership/Setup
tab of the Link Aggregation
page to specify the members of a trunk.
To define the members of a trunk:
1
On the
Membership/Setup
tab, select the same trunk
number under Group Membership for the ports that you
want to trunk.
For example, if you want ports 2, 3, 4, and 5 to become
members of Trunk 2, set the Group Membership for
these ports to 2.
2
Click
Apply
.