Acer H9500BD User Manual - Page 47

Replacing the Lamp - replacement bulb

Get Acer H9500BD PDF manuals and user guides View all Acer H9500BD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

English SOURCE 37 Replacing the Lamp Use a screwdriver to remove the screw(s) from the cover, and then pull out the lamp. The projector will detect the lamp life. You will be shown a warning message "Lamp is approaching the end of its useful life in full power operation. Replacement Suggested!" When you see this message, change the lamp as soon as possible. Make sure the projector has been cooling down for at least 30 minutes before changing the lamp. Warning: The lamp compartment is hot! Allow it to cool down before changing the lamp. LAMP RESYNC MENU TEMP 1 4 3 2 To Change the Lamp 1 Turn off the projector by pressing the power button. 2 Allow the projector at least 30 mins to cool down. 3 Disconnect the power cord. 4 Find the "OPEN" button on side of the projector and push it to open the cover. (Illustration #1) 5 Open the cover. (Illustration #2) 6 Remove the two screws that secure the lamp module.(Illustration #3) 7 Pull out the lamp module by force. (Illustration #4) To replace the lamp module, reverse the previous step. Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
37
English
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.
The projector will detect the lamp life. You will be shown a warning message
"
Lamp is approaching the end of its useful life in full power operation.
Replacement Suggested!
" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooling down for at least 30
minutes before changing the lamp.
Warning:
The lamp compartment is hot! Allow it to cool down
before changing the lamp.
To Change the Lamp
1
Turn off the projector by pressing the power button.
2
Allow the projector at least 30 mins to cool down.
3
Disconnect the power cord.
4
Find the "OPEN" button on side of the projector and push it to open the
cover. (Illustration #1)
5
Open the cover. (Illustration #2)
6
Remove the two screws that secure the lamp module.(Illustration #3)
7
Pull out the lamp module by force. (Illustration #4)
To replace the lamp module, reverse the previous step.
Warning:
To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
1
2
3
4