Acer X1261P User Manual - Page 38

Problems with the Projector, Condition, Solution

Get Acer X1261P PDF manuals and user guides
UPC - 884483891955
View all Acer X1261P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

28 English 9 Image is too small • or too large • • 10 Image has slanted • sides • • 11 Image is reversed • Adjust the zoom lever on the front of the projector. Move the projector closer to or further from the screen. Press "MENU" on the remote control. Go to "Image --> Aspect Ratio" and try different settings or press"Aspect Ratio" on the remote control to adjust directly. If possible, reposition the projector so that it is centered on the screen. Press the "Keystone / " button on the remote control until the sides are vertical. Press "MENU" on the remote control. Go to "Image -> Auto Keystone" and choose "Off" on the OSD, if "Keystone" button is not available on the remote control. Select "Image --> Projection" on the OSD and adjust the projection direction. Problems with the Projector # Condition Solution 1 The projector stops responding If possible, turn off the projector, then to all controls unplug the power cord and wait at least 30 seconds before reconnecting power. 2 Lamp burns out or makes a popping sound When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
28
English
Problems with the Projector
9
Image is too small
or too large
•
Adjust the zoom lever on the front of the projector.
•
Move the projector closer to or further from the
screen.
•
Press "
MENU
" on the remote control. Go to "Image
--> Aspect Ratio" and try different settings or
press"
Aspect Ratio
" on the remote control to adjust
directly.
10
Image has slanted
sides
•
If possible, reposition the projector so that it is
centered on the screen.
•
Press the "
Keystone
/
" button on the remote
control until the sides are vertical.
•
Press "
MENU
" on the remote control. Go to "Image -
-> Auto Keystone" and choose "Off" on the OSD, if
"
Keystone
" button is not available on the remote
control.
11
Image is reversed
•
Select "Image --> Projection" on the OSD and adjust
the projection direction.
#
Condition
Solution
1
The projector stops responding
to all controls
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
2
Lamp burns out or makes a
popping sound
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.