Adaptec FS4500 User Guide - Page 47

Hot-swapping the ES Module, Removing the ES Module, Installing an ES Module

Get Adaptec FS4500 - Hard Drive Array PDF manuals and user guides
UPC - 760884144275
View all Adaptec FS4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Removing and Replacing Enclosure Components Hot-swapping the ES Module This section provides removal and installation instructions for your Storage Enclosure's ES modules. For detailed information about the ES module and how it works, see About the ES Module on page 3-2. The ES module is located on the rear of the Storage Enclosure between the two APCs, as shown in Figure 1-1 on page 1-4. The ES module is hot-swappable; removing the ES module does not impact the data path. Removing the ES Module To remove the ES module from the Storage Enclosure: 1 Using a Phillips-head screwdriver, loosen the screw that secures the module to the enclosure. 2 Grasp the ES module handle and gently pull the module from the enclosure. Be sure to pull straight back and not to one side. The cooling fans switch to high speed. Warning: To avoid electrical shock, do not insert any instruments or tools into the open ES module slot. Installing an ES Module To install an ES module in the Storage Enclosure: 1 With the handle toward you, slide the ES module straight into the enclosure slot. 2 Gently push the module until the connectors engage. 3 Secure the module using the screw you loosened in Step 1 on page 4-10. Hand tighten the screw. Do not over-tighten it. The ES module automatically reboots and enclosure services are reactivated. (See Chapter 3, Monitoring for more information.) 4-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
4-10
Removing and Replacing Enclosure Components
Hot-swapping the ES Module
This section provides removal and installation instructions for
your Storage Enclosure’s ES modules. For detailed information
about the ES module and how it works, see
About the ES Module
on
page 3-2
.
The ES module is located on the rear of the Storage Enclosure
between the two APCs, as shown in
Figure 1-1 on page 1-4
.
The ES module is hot-swappable; removing the ES module does
not impact the data path.
Removing the ES Module
To remove the ES module from the Storage Enclosure:
1
Using a Phillips-head screwdriver, loosen the screw that
secures the module to the enclosure.
2
Grasp the ES module handle and gently pull the module from
the enclosure. Be sure to pull straight back and not to one side.
The cooling fans switch to high speed.
Warning:
To avoid electrical shock,
do not
insert any
instruments or tools into the open ES module slot.
Installing an ES Module
To install an ES module in the Storage Enclosure:
1
With the handle toward you, slide the ES module straight into
the enclosure slot.
2
Gently push the module until the connectors engage.
3
Secure the module using the screw you loosened in
Step 1 on
page 4-10
. Hand tighten the screw.
Do not
over-tighten it.
The ES module automatically reboots and enclosure services are
reactivated. (See
Chapter 3,
Monitoring
for more information.)