Alpine IDA X200 Owners Manual - Page 22

Turning Subwoofer ON/OFF When the subwoofer is on, you can adjust the subwoofer output level (refer to page 19). For iDA-X200, the following setting can be made only when the IMPRINT audio processor (PXA-H100) is not connected. 1 Press and hold IMPRINT (iDA-X200 only) or SOUND (iDA-X300 only) for at least 2 seconds to activate the AUDIO selection mode. 2 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the SUBW mode, and then press /ENTER. SUBW SUBW SYSTEM* BASS TREBLE HPF SUBW * Displayed only when subwoofer is ON. 3 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select SUBW ON/OFF, and then press /ENTER. ON OFF 4 Press to return to normal mode. • If no operation is performed for 15 seconds, the unit will return to normal mode automatically. • If is pressed during setting, the unit returns to the previous item. Setting the Subwoofer System When the subwoofer is on, you can select either SYS 1 or SYS 2 for the desired subwoofer effect. For iDA-X200, the following setting can be made only when the IMPRINT audio processor (PXA-H100) is not connected. 1 Press and hold IMPRINT (iDA-X200 only) or SOUND (iDA-X300 only) for at least 2 seconds to activate the AUDIO selection mode. 2 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the SUBW SYSTEM mode, and then press /ENTER. SUBW SUBW SYSTEM* HPF SUBW BASS TREBLE * Displayed only when subwoofer is ON. 3 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the SUBW SYS 1 or SUBW SYS 2, and then press /ENTER. SYS 1 4 Press SYS 2 to return to normal mode. • If no operation is performed for 15 seconds, the unit will return to normal mode automatically. • If is pressed during setting, the unit returns to the previous item. • This function is inoperable when Subwoofer is set to OFF. Setting the Bass Control You can change the Bass Frequency emphasis to create your own tonal preference. For iDA-X200, the following setting can be made only when the IMPRINT audio processor (PXA-H100) is not connected. 1 Press and hold IMPRINT (iDA-X200 only) or SOUND (iDA-X300 only) for at least 2 seconds to activate the AUDIO selection mode. 2 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the BASS Adjustment mode, and then press /ENTER. SUBW SUB SYSTEM* BASS TREBLE HPF SUBW * Displayed only when subwoofer is ON. Setting the Bass Level 3-1*1Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the desired bass level (-7~+7), and then press /ENTER. You can emphasize or weaken the bass level. Setting the Bass Bandwidth 3-2 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the desired bass bandwidth, and then press /ENTER. Changes the boosted bass bandwidth to wide or narrow. A wider setting will boost a wide range of frequencies above and below the center frequency. A narrower setting will boost only frequencies near the center frequency. Setting the Bass Center Frequency 3-3 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the desired bass center frequency, and then press /ENTER. 80(Hz) 100(Hz) 200(Hz) 60(Hz) 80(Hz) Emphasizes the displayed bass frequency ranges. 4 Press to return to normal mode. • If no operation is performed for 15 seconds, the unit will return to normal mode automatically. • If is pressed during setting, the unit returns to the previous item. • The function is inoperable when DEFEAT is set to ON. *1 The adjustment can also be made by pressing IMPRINT (iDA-X200 only) or SOUND (iDA-X300 only). Refer to "Adjusting Subwoofer/ Bass/Treble/Balance(Between Left and Right)/Fader (Between Front and Rear)/Loudness/Defeat" (page 19). 20-EN