Home » Asus Manuals » Motherboards » Asus P5KPL SE » Manual Viewer

Asus P5KPL SE User Manual - Page 31

P5KPL SE IDE connector

Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

3. IDE connector (40-1 pin PRI_EIDE) The onboard IDE connector is for the Ultra DMA 100/66/33 signal cable. There are three connectors on each Ultra DMA 100/66/33 signal cable: blue, black, and gray. Connect the blue connector to the motherboard's IDE connector, then select one of the following modes to configure your device. Single device Two devices Drive jumper setting Cable-Select or Master Cable-Select Master Slave Mode of device(s) Master Slave Master Slave Cable connector Black Black Gray Black or gray • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 100/66/33 IDE devices. PRI_IDE If any device jumper is set as "Cable-Select," make sure all other device jumpers have the same setting. PIN1 P5KPL SE NOTE:Orient the red markings on the IDE ribbon cable to PIN 1. P5KPL SE IDE connector 4. Digital audio connector (4-1 pin SPDIF_OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port. Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis. SPDIFOUT GND +5V P5KPL SE SPDIF_OUT P5KPL SE Digital audio connector The S/PDIF module is purchased separately. ASUS P5KPL SE 1-21

Section	Page
Notices	6
Safety information	7
About this guide	7
P5KPL SE specifications summary	9
Chapter 1	11
Product introduction	11
1.1 Welcome!	11
1.2 Package contents	11
1.3 Special features	11
1.3.1 Product highlights	11
1.3.2 ASUS unique features	12
1.3.3 ASUS Intelligent Overclocking features	13
1.4 Before you proceed	14
1.5 Motherboard overview	15
1.5.1 Placement direction	15
1.5.2 Screw holes	15
1.5.3 Motherboard layout	16
1.5.4 Layout contents	17
1.6 Central Processing Unit (CPU)	17
1.6.1 Installing the CPU	18
1.6.2 Installing the CPU heatsink and fan	20
1.6.3 Uninstalling the CPU heatsink and fan	21
1.7 System memory	21
1.7.1 Overview	21
1.7.2 Memory configurations	22
1.7.3 Installing a DIMM	26
1.7.4 Removing a DIMM	26
1.8 Expansion slots	27
1.8.1 Installing an expansion card	27
1.8.2 Configuring an expansion card	27
1.8.4 PCI slots	27
1.8.5 PCI Express x1 slot	27
1.8.6 PCI Express x16 slot	27
1.9 Jumper	28
1.10 Connectors	29
1.10.1 Rear panel connectors	29
1.10.2 Internal connectors	30
1.11 Software support	37
1.11.1 Installing an operating system	37
1.11.2 Support DVD information	37
Chapter 2	39
BIOS information	39
2.1 Managing and updating your BIOS	39
2.1.1 ASUS Update utility	39
2.1.2 Creating a bootable floppy disk	40
2.1.3 ASUS EZ Flash 2 utility	41
2.1.4 AFUDOS utility	42
2.1.5 ASUS CrashFree BIOS 3 utility	43
2.2 BIOS setup program	45
2.2.1 BIOS menu screen	46
2.2.2 Menu bar	46
2.2.3 Navigation keys	46
2.2.4 Menu items	47
2.2.5 Sub-menu items	47
2.2.6 Configuration fields	47
2.2.7 Pop-up window	47
2.2.8 Scroll bar	47
2.2.9 General help	47
2.3 Main menu	48
2.3.1 System Time	48
2.3.2 System Date	48
2.3.3 Legacy Diskette A	48
2.3.4 Primary IDE Master/Slave, SATA 1~4	48
2.3.5 Storage Configuration	49
2.3.6 System Information	49
2.4 Advanced menu	50
2.4.1 JumperFree Configuration	50
2.4.2 USB Configuration	52
2.4.3 CPU Configuration	52
2.4.4 Chipset	53
2.4.5 Onboard Devices Configuration	54
2.4.6 PCI PnP	54
2.5 Power menu	55
2.5.1 Suspend Mode	55
2.5.2 ACPI 2.0 Support	55
2.5.3 ACPI APIC Support	56
2.5.4 APM Configuration	56
2.5.5 Hardware Monitor	56
2.6 Boot menu	57
2.6.1 Boot Device Priority	57
2.6.2 Boot Settings Configuration	57
2.6.3 Security	58
2.7 Tools menu	59
2.7.1 ASUS EZ Flash 2	59
2.7.2 AI NET 2	60