Asus PRL-DLS533 User Guide - Page 123

Installing the Driver Software

Get Asus PRL-DLS533 PDF manuals and user guides View all Asus PRL-DLS533 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 123 highlights

NT4 5.3.2 Broadcom Gigabit LAN Driver Installation W2K WXP NNW Installing the Driver Software SCO UNX LNX To install the adapter software for Windows2000, do the following NOTE - Before beginning this procedure, verify that the Windows 2000 system has been upgraded to the latest version with the latest service pack applied. 1. Start your Windows2000 system and log in. You must have System Administrator privileges to install the driver software. When you boot up the Windows2000 system after installing the adapter card, a series of "Found New Hardware Wizard" windows are displayed. 2. In the Install Hardware Device Drivers window, click Search for a suitable driver for my device (recommended), then click Next. 3. In the Locate Driver Files window, select the applicable search location check boxes. 4. When prompted, insert the media to be searched into your CD-ROM drive, type the path to the driver, and select OK. Example: e:\ Where "e:" is the designation of the CD-ROM drive on your system. 5. In the Driver Files Search Results window, verify that the correct path to the driver software is shown, then click Next. NOTE - If the Insert Disk window appears, do not insert the Windows2000 disk. Some early versions of Windows2000 may display a spurious message requesting you to insert the Windows2000 disk. If this occurs, leave the driver installation media in the drive and click OK. If asked to specify the location of the Windows2000 CD-ROM instead, click Browse (don't use the text entry field) and locate the path to the Gigabit Ethernet drivers that was specified above. 5-20 Chapter 5: Driver installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
5-20
Chapter 5: Driver installation
NT4
W2K
WXP
NNW
SCO
UNX
LNX
5.3.2
Broadcom Gigabit LAN Driver Installation
Installing the Driver Software
To install the adapter software for Windows2000, do the following
NOTE – Before beginning this procedure, verify that the Windows
2000
system has been upgraded to the latest version with the latest service
pack applied.
1.
Start your Windows2000 system and log in. You must have System
Administrator privileges to install the driver software. When you boot
up the Windows2000 system after installing the adapter card, a series
of “Found New Hardware Wizard” windows are displayed.
2.
In the Install Hardware Device Drivers window, click
Search for a
suitable driver for my device (recommended)
, then click Next.
3.
In the Locate Driver Files window, select the applicable search location
check boxes.
4.
When prompted, insert the media to be searched into your CD-ROM
drive, type the path to the driver, and select
OK
.
Example: e:\
Where “e:” is the designation of the CD-ROM drive on your system.
5.
In the Driver Files Search Results window, verify that the correct path to
the driver software is shown, then click
Next
.
NOTE – If the Insert Disk window appears, do not insert the
Windows2000 disk.
Some early versions of Windows2000 may display a spurious message
requesting you to insert the Windows2000 disk. If this occurs, leave the
driver installation media in the drive and click
OK
. If asked to specify the
location of the Windows2000 CD-ROM instead, click
Browse
(don’t use
the text entry field) and locate the path to the Gigabit Ethernet drivers that
was specified above.