Asus RAMPAGE IV EXTREME User Manual

Asus RAMPAGE IV EXTREME Manual

Get Asus RAMPAGE IV EXTREME PDF manuals and user guides View all Asus RAMPAGE IV EXTREME manuals
Add to My Manuals
Save this manual to your list of manuals

Asus RAMPAGE IV EXTREME manual content summary:

  • Asus RAMPAGE IV EXTREME | User Manual - Page 1
    Motherboard RAMPAGE IV EXTREME
  • Asus RAMPAGE IV EXTREME | User Manual - Page 2
    A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE code as required under various Free Open Source Software licenses. If however you encounter any problems in obtaining the full corresponding source code
  • Asus RAMPAGE IV EXTREME | User Manual - Page 3
    in this guide xiv Typography...xiv RAMPAGE IV EXTREME specifications summary xv Chapter 1: Product introduction 1.1 Welcome!...1-1 1.2 Package contents 1-1 1.3 Special features 1-2 1.3.1 Product highlights 1-2 1.3.2 ROG Intelligent Performance & Overclocking features 1-3 1.3.3 Sound
  • Asus RAMPAGE IV EXTREME | User Manual - Page 4
    LEDs 2-22 2.2.7 Jumper 2-30 2.2.8 Internal connectors 2-31 2.3 Building your computer system 2-42 2.3.1 Additional tools and components to build a PC system 2-42 2.3.2 CPU installation 2-43 2.3.3 CPU heatsink and fan assembly installation 2-45 2.3.4 DIMM installation 2-47 2.3.5 Motherboard
  • Asus RAMPAGE IV EXTREME | User Manual - Page 5
    File 3-40 3.9 Exit menu 3-41 3.10 Updating BIOS 3-42 3.10.1 ASUS Update utility 3-42 3.10.2 ASUS EZ Flash Utility 3-46 3.10.3 ASUS CrashFree BIOS 3 utility 3-47 3.10.4 ASUS BIOS Updater 3-48 3.10.5 USB BIOS Flashback 3-51 Chapter 4: Software support 4.1 Installing an operating system
  • Asus RAMPAGE IV EXTREME | User Manual - Page 6
    Windows® OS installation....... 4-29 Using a USB floppy disk drive 4-30 Chapter 5: Multiple GPU technology support 5.1 AMD® CrossFireX™ technology 5-1 5.1.1 Requirements 5-1 5.1.2 Before you begin 5-1 5.1.3 Installing two CrossFireX™ graphics cards 5-2 5.1.4 Installing the device drivers
  • Asus RAMPAGE IV EXTREME | User Manual - Page 7
    and, if not installed and used in accordance with manufacturer's instructions, may cause harmful interference to radio communications. However, there user's authority to operate this equipment. "The manufacture declares that this device is limited to Channels 1 through 11 in the 2.4GHz frequency by
  • Asus RAMPAGE IV EXTREME | User Manual - Page 8
    spectrum as in [Article 3.2] • Radio test suites according to [EN 300 328-2] CE Mark Warning CE marking for devices without wireless LAN/Bluetooth The shipped version of this device complies with the requirements of the EEC directives 2004/108/EC "Electromagnetic compatibility" and 2006/95/EC "Low
  • Asus RAMPAGE IV EXTREME | User Manual - Page 9
    for frequencies between 2446.5 MHz and 2483.5 MHz Channels 10 through 13 inclusive operate in the band 2446.6 MHz to property is not permitted. In the departments listed below, for the entire 2.4 GHz band: time, allowing you to use your wireless LAN card in more areas within France. Please check
  • Asus RAMPAGE IV EXTREME | User Manual - Page 10
    , including interference that may cause undesired operation of the device. To prevent radio interference to the licensed service (i.e. co-channel Mobile Satellite systems) this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit
  • Asus RAMPAGE IV EXTREME | User Manual - Page 11
    the existing system before you add a device. • Before connecting or removing signal cables from the motherboard, ensure that a qualified service technician or your retailer. • The optical S/PDIF is an optional component (may or may not be included in your motherboard) and is RELATED INSTRUCTIONS. xi
  • Asus RAMPAGE IV EXTREME | User Manual - Page 12
    where it may become wet. This motherboard should only be used in environments with ambient temperatures between 5ºC (41ºF) and 40ºC (104ºF). • Place the product on a stable surface. • If you encounter technical problems with the product, contact a qualified service technician or your retailer. REACH
  • Asus RAMPAGE IV EXTREME | User Manual - Page 13
    new technology it supports. • Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the switches, jumpers, and connectors on the motherboard. • Chapter 3: BIOS setup This chapter tells
  • Asus RAMPAGE IV EXTREME | User Manual - Page 14
    of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete
  • Asus RAMPAGE IV EXTREME | User Manual - Page 15
    RAMPAGE IV EXTREME specifications summary CPU Chipset Memory Expansion Slots Multi-GPU Technology Storage LAN High Definition Audio Bluetooth USB 2ndGeneration Intel® Core™ i7 Processor Family for the LGA 2011 Socket Supports Intel® Turbo Boost Technology 2.0 * Refer to www.asus.com for Intel CPU
  • Asus RAMPAGE IV EXTREME | User Manual - Page 16
    TweakIt ROG iDirect GPU.DIMM Post ROG Extreme Engine Digi+ II - �8��p�h�a�s�e�C��P�U��p�o�w�e�r - �3��p�h�a�s�e�V�C��C�S�A��p�o�w�e�r - 2+2 phase DRAM power ProbeIt iROG Extreme Tweaker USB BIOS Flashback BIOS Flashback with onboard switch button Loadline Calibration Intelligent overclocking tools
  • Asus RAMPAGE IV EXTREME | User Manual - Page 17
    Flash 2 - ASUS MyLogo 3 - ROG BIOS Wallpaper ASUS Q-Design - ASUS Q-Connector - ASUS Q-LED (CPU, DRAM, VGA, Boot Device LED) - ASUS Q-Slot - ASUS Q-DIMM 1 x PS/2 keyboard/mouse port 1 x Clr CMOS switch 1 x ROG Connect On/Off button 2 x External SATA 6.0 Gb/s ports 1 x LAN (RJ45) port 1 x Bluetooth
  • Asus RAMPAGE IV EXTREME | User Manual - Page 18
    RAMPAGE IV EXTREME specifications summary BIOS Features 2 x 64Mb Flash ROMs, UEFI AMI BIOS, PnP, DMI2.0, WfM2.0, SM BIOS 2.5, ACPI2.0a Multi-Language BIOS Manageability WfM2.0, DMI2.0, WOL by PME, WOR by PME, PXE Software Support DVD: Drivers and applications - Kaspersky® Anti-Virus 1-year
  • Asus RAMPAGE IV EXTREME | User Manual - Page 19
    of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items. Motherboard ROG RAMPAGE IV EXTREME Accessories 1�x�R�O�G�C�on
  • Asus RAMPAGE IV EXTREME | User Manual - Page 20
    motherboard is ready to support PCIe 3.0 SPEC. Functions will be available when using PCIe 3.0-compliant devices. Please refer to www.asus.com for updated details. SLI/CrossFire On-Demand Why choose when you can have both? SLI or CrossFireX? Fret no longer because with the ROG RAMPAGE IV EXTREME
  • Asus RAMPAGE IV EXTREME | User Manual - Page 21
    performance with adjustable CPU and memory power management frequencies. Precise adjustments create greater efficiency, stability, five times stronger lifespan than solid capacitors* and performance for total system control. (*At an operating temperature of 105°C) ROG RAMPAGE IV EXTREME 1-3
  • Asus RAMPAGE IV EXTREME | User Manual - Page 22
    DIMMs status in the BIOS, potentially keeping that record-breaking overclock! ProbeIt Get all hands-on with hardware-based overclocking. ProbeIt takes the guesswork out of locating the motherboard's measurement points, identifying them clearly in the form of eight sets of detection points so you'll
  • Asus RAMPAGE IV EXTREME | User Manual - Page 23
    as the "red zone" of a tachometer, the Voltiminder LED displays the voltage status for CPU, NB, SB, and Memory in a intuitive color-coded fashion. The voltiminder LED allows quick voltage monitoring for overclockers. COP EX Maximum OC with confidence with burn proof protection to chipsets and GPU
  • Asus RAMPAGE IV EXTREME | User Manual - Page 24
    With an easy press during overclock, this exclusive onboard switch allows gamer to effortlessly fine-tune the performance without having to short the pins or moving jumpers! Q-Fan Plus Optimized quietness and cooling for more devices! The Q-Fan function automatically detects temperature and adjusts
  • Asus RAMPAGE IV EXTREME | User Manual - Page 25
    Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before to do so may cause severe damage to the motherboard, peripherals, or components. ROG RAMPAGE IV EXTREME 2-1
  • Asus RAMPAGE IV EXTREME | User Manual - Page 26
    2.2 Motherboard overview 2.2.1 Motherboard layout Chapter 2 Refer to 2.2.8 Internal connectors and 2.3.10 Rear panel connection for more information about rear panel connectors and internal connectors. 2-2 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 27
    black]) 19. Intel X79 Serial ATA 6Gb/s connectors (7-pin SATA6G_1/2 [red]) 20. ASMedia Serial ATA 6Gb/s connectors (7-pin SATA6G_E1/E2 [red]) 21. BIOS button 22. System panel connector (20-8 pin PANEL) 23. USB 2.0 connectors (10-1 pin USB910; USB1112) 24. BIOS LED 25. Front panel audio
  • Asus RAMPAGE IV EXTREME | User Manual - Page 28
    . ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA2011 socket. • The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal
  • Asus RAMPAGE IV EXTREME | User Manual - Page 29
    The motherboard comes with four Double Data Rate 3 (DDR3) Dual Inline Memory Modules (DIMM) slots. A DDR3 module is notched differently from a DDR or DDR2 module. DO NOT install a DDR or DDR2 memory module to the DDR3 slot. Recommended memory configurations Chapter 2 ROG RAMPAGE IV EXTREME 2-5
  • Asus RAMPAGE IV EXTREME | User Manual - Page 30
    at the vendor-marked or at a higher frequency, refer to section 3.3 Extreme Tweaker menu for manual memory frequency adjustment. • For system stability, use a more efficient memory cooling system to support a full memory load (8 DIMMs) or overclocking condition. 2-6 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 31
    ( 2x DS - - 2GB ) Timing Voltage 10-11-10- 1.65 30 9-11-9-27 1.65 9-11-9-28 1.65 9-11-9-27 1.65 DIMM socket support (Optional) 2 DIMM 4 DIMM 6 DIMM 8 DIMM • • • • • - 1.65 • • • 9-11-9-27 1.66 • • RAMPAGE IV EXTREME Motherboard Qualified Vendors Lists (QVL) DDR3 2250 MHz capability
  • Asus RAMPAGE IV EXTREME | User Manual - Page 32
    • • - - • • • • • • • - • • • • • • • • • • • - • • • • • • • • RAMPAGE IV EXTREME Motherboard Qualified Vendors Lists (QVL) DDR3 10-9-27 9-10-9-28 9-9-9-24 9-10-9-28 9-9-9-24 9-9-9 9-9-9 9-9-9-24 9-11-9-27 9-9-9-24 Voltage 1.55~1.75 1.55~1.75 1.5 DIMM socket support
  • Asus RAMPAGE IV EXTREME | User Manual - Page 33
    Brand Chip NO. Timing DS DS - - 9-9-9-24 DS - - - Voltage DIMM socket support (Optional) 2 DIMM 4 DIMM 6 DIMM 8 DIMM 1.6 • • - - 1.65 • • • • RAMPAGE IV EXTREME Motherboard Qualified Vendors Lists (QVL) DDR3 1600 MHz capability Vendors A-DATA A-DATA A-DATA CORSAIR CORSAIR CORSAIR
  • Asus RAMPAGE IV EXTREME | User Manual - Page 34
    9 1.65 9 1.65 (DDR3 1600 MHz continues on next page) DIMM socket support (Optional) 2 DIMM 4 DIMM 6 DIMM 8 DIMM • • - • • - - - • - - • • - - • • • • • • • - • • - - • • • - - • - - • • • - • • • - • • • - 2-10 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 35
    1.65 1.7 1.7 1.7 1.65 1.65 1.65 DIMM socket support (Optional) 2 DIMM 4 DIMM 6 DIMM 8 DIMM - - • • - - • • • • • • - - • • • • • • - - - • - - • • • • • • • - • • • • • • - - • • • - • • • - • • • - Chapter 2 ROG RAMPAGE IV EXTREME 2-11
  • Asus RAMPAGE IV EXTREME | User Manual - Page 36
    Chapter 2 RAMPAGE IV EXTREME Motherboard Qualified Vendors Lists (QVL) DDR3 1333 MHz MHz continues on next page) Voltage 1.25~1.35 1.5 DIMM socket support (Optional) 2 DIMM 4 DIMM 6 DIMM 8 DIMM • • • - • • • • • • • • • • • • • • • - • • • • • • • • • - - - 1.5
  • Asus RAMPAGE IV EXTREME | User Manual - Page 37
    10-A0 PC310600U-9-10 - - - - - - - - - - 9 - K4B2G0846C - - - DIMM socket support (Optional) 2 DIMM 4 DIMM 6 DIMM 8 DIMM • • • • • • - • • • - • • • • • • • - • • • - • • • - • • • - (DDR3 1333 MHz continues on next page) ROG RAMPAGE IV EXTREME 2-13
  • Asus RAMPAGE IV EXTREME | User Manual - Page 38
    Team T3D1288LT-13 7-7-7-21 Team TXD31048M1333C7-D(XMP) 1GB SS Team T3D1288LT-13 7-7-7-21 Team TXD32048M1333C7-D(XMP) 2GB DS Team T3D1288LT-13 7-7-7-21 Voltage - DIMM socket support (Optional) 2 DIMM 4 DIMM 6 DIMM 8 DIMM
  • Asus RAMPAGE IV EXTREME | User Manual - Page 39
    RAMPAGE IV EXTREME Motherboard Qualified Vendors Lists (QVL) DDR3 1067 MHz capability Vendors Part No. Size SS/ Chip Brand Chip NO. DS ELPIDA ELPIDA GEIL Hynix Kingston KINGSTON Kingston KINGSTON KINGSTON SAMSUNG
  • Asus RAMPAGE IV EXTREME | User Manual - Page 40
    . • While running at heavy loaded four VGA cards, ensure to plug in the 6-pin extra PCIe power supply for stability. • Connect a chassis fan to the motherboard connector labeled CHA_FAN1/2/3 when using multiple graphics cards for better thermal environment. 2-16 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 41
    IRQ assignments for this motherboard A B C D E F G H PCIE_X16_1 shared - - - - - - - PCIE_X8_2A shared - - - - - - High Definition Audio - - - - - - shared - SATA #0 - - shared - - - - - SATA #0 - - - - shared - - - Chapter 2 ROG RAMPAGE IV EXTREME 2-17
  • Asus RAMPAGE IV EXTREME | User Manual - Page 42
    on a bare or opencase system. This is ideal for overclockers and gamers who continually change settings to enhance system performance. 1. Power-on switch Press the power-on switch to wake/power up the system. 2. Reset switch Press the reset switch to reboot the system. Chapter 2 2-18 Chapter
  • Asus RAMPAGE IV EXTREME | User Manual - Page 43
    load the preset profile (GO_Button file) for temporary overclocking when in OS. 4. BIOS button The motherboard comes with two BIOS. Press the BIOS button to switch BIOS and load different BIOS settings. The nearby BIOS LEDs indicate the BIOS you are using. Chapter 2 ROG RAMPAGE IV EXTREME 2-19
  • Asus RAMPAGE IV EXTREME | User Manual - Page 44
    to find out the faulty one without removing the cards. 6. Q reset button When the LN2_Mode jumper does not work and your CPU cannot resume function, press the Q reset button to temporarily stop the power supply to the CPU and help the CPU recover from a frozen condition. Chapter 2 2-20 Chapter
  • Asus RAMPAGE IV EXTREME | User Manual - Page 45
    . Switching over to Slow-Mode during critical moments when Temperature/Max Frequency alignment is off-synch saves you a lot of crashes, even when trying to boot into the OS at cold temperatures. Chapter 2 ROG RAMPAGE IV EXTREME 2-21
  • Asus RAMPAGE IV EXTREME | User Manual - Page 46
    when debugging overclock failures. Voltiminder LED II consists of the following LED set: GND, CPU_VCORE, CPU_VSA, CPU_VTT, PCH_1.1V, PCH_1.5V, DRAM_AB, and DRAM_CD. For example, when you fail to post and see the LED for CPU_VTT light up, the system is alerting you that the setting for CPU VTT should
  • Asus RAMPAGE IV EXTREME | User Manual - Page 47
    drive connected to the motherboard or when the hard disk drive does not function. 3. BIOS LED The BIOS LEDs help indicate the BIOS activity. Press the BIOS button to switch between BIOS1 and BIOS2 and the LED lights up when the corresponding BIOS is in use. Chapter 2 ROG RAMPAGE IV EXTREME 2-23
  • Asus RAMPAGE IV EXTREME | User Manual - Page 48
    (GO_Button file) for temporary overclocking when in OS. 5. Q LED Q LEDs check key components (CPU, DRAM, VGA card, and booting devices) in sequence during motherboard booting process. If an error is found , the corresponding LED will continue lighting until the problem is solved. This user-friendly
  • Asus RAMPAGE IV EXTREME | User Manual - Page 49
    in any motherboard component. The illustration below shows the location of the onboard power-on switch. 7. Debug LEDs The Debug LED design provides you the 2-digit display, allowing you to know the system status. Refer to the Debug table below for details. Chapter 2 ROG RAMPAGE IV EXTREME 2-25
  • Asus RAMPAGE IV EXTREME | User Manual - Page 50
    OEM initialization after microcode loading Cache initialization Reserved for future AMI SEC error codes Microcode not found Microcode not loaded PEI Core is started Pre-memory CPU initialization is started Pre-memory System Agent initialization is started Pre-memory PCH initialization is started OEM
  • Asus RAMPAGE IV EXTREME | User Manual - Page 51
    or Speed CPU mismatch CPU self test failed or possible CPU cache error CPU micro-code is not found or micro-code update is failed Internal CPU error Reset PPI is not available Reserved for future AMI error codes S3 Resume is stared (S3 Resume PPI is called by the DXE IPL) S3 Boot Script execution
  • Asus RAMPAGE IV EXTREME | User Manual - Page 52
    PCI Bus Assign Resources Console Output devices connect Console input devices connect Super IO Initialization USB initialization is started USB Reset USB Detect USB Enable Reserved for future AMI codes IDE initialization is started IDE Reset IDE Detect IDE Enable SCSI initialization is started
  • Asus RAMPAGE IV EXTREME | User Manual - Page 53
    Input Devices are found Invalid password Error loading Boot Option (LoadImage returned error) Boot Option is failed (StartImage returned error) Flash update is failed Reset protocol is not available *ASL Status Codes Status Code 01 02 03 04 05 10 20 30 40 AC AA Description System is entering
  • Asus RAMPAGE IV EXTREME | User Manual - Page 54
    2.2.7 Jumper 1. LN2 Mode Jumper (3-pin LN2) With LN2 mode activated, the ROG motherboard is optimized to remedy the coldboot bug during POST at an extremely low temperature and help the system boot successfully. 2. OT header (ROG Connect switch) The OT header allows connection of a 2-pin cable
  • Asus RAMPAGE IV EXTREME | User Manual - Page 55
    Configuration for details. • Before creating a RAID set, refer to section 4.4 RAID configurations or the manual bundled in the motherboard support DVD. • When using NCQ, set the SATA Mode in the BIOS to [AHCI Mode]. Refer to section 3.5.3 SATA Configuration for details. ROG RAMPAGE IV EXTREME 2-31
  • Asus RAMPAGE IV EXTREME | User Manual - Page 56
    can create a RAID 0, 1, 5, and 10 configuration with the Intel® Rapid Storage Technology through the onboard Intel® X79 chipset. • These connectors are set to [AHCI RAID configurations or the manual bundled in the motherboard support DVD. • When using NCQ, set the SATA Mode in the BIOS to [AHCI Mode
  • Asus RAMPAGE IV EXTREME | User Manual - Page 57
    hard disk drives via Serial ATA 6.0 Gb/s signal cables. Chapter 2 • The SATA6G_E1/E2 (red) connectors are for data drives only. ATAPI device is not supported. • You must install Windows® XP Service Pack 3 or later versions before using Serial ATA hard disk drives. • When using NCQ, set the Asmedia
  • Asus RAMPAGE IV EXTREME | User Manual - Page 58
    3.0 ports, and complies with the USB 3.0 specificaton that supports up to 4.8Gbps connection speed. If the USB 3.0 front panel cable is available from your system chassis, with this USB 3.0 connector, you can have a front panel USB 3.0 solution. Chapter 2 The USB 3.0 module is purchased separately
  • Asus RAMPAGE IV EXTREME | User Manual - Page 59
    the motherboard! You can connect the front panel USB cable to the ASUS Q-Connector (USB, blue) first, and then install the Q-Connector (USB) to the USB connector onboard if your chassis supports front panel USB ports. The USB 2.0 module is purchased separately. Chapter 2 ROG RAMPAGE IV EXTREME
  • Asus RAMPAGE IV EXTREME | User Manual - Page 60
    the module to a slot opening at the back of the system chassis. Chapter 2 The S/PDIF module is purchased separately. 9. VGA Hotwire Connector The VGA Hotwire connector allows you to precisely adjust the VGA card voltage directly from motherboard BIOS, OC Key or TurboV EVO, reducing the risk of
  • Asus RAMPAGE IV EXTREME | User Manual - Page 61
    fan connectors! • The CPU_FAN connector supports the CPU fan of maximum 1A (12 W) fan power. • If you install two VGA cards, we recommend that you plug the rear chassis fan cable to the motherboard connector labeled CHA_FAN1 or CHA_FAN2 for better thermal environment. ROG RAMPAGE IV EXTREME 2-37
  • Asus RAMPAGE IV EXTREME | User Manual - Page 62
    audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. • We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard's high-definition audio
  • Asus RAMPAGE IV EXTREME | User Manual - Page 63
    (or later version) and provides a minimum power of 450 W. • Do not forget to connect the 4-pin/8-pin EATX12 V power plug; otherwise, the system will not boot. • Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become
  • Asus RAMPAGE IV EXTREME | User Manual - Page 64
    cable to EZ_PLUG_2 to provide stable power supply to the DIMMs. 14. OC Key connector (10-1 pin OC Key) Connects to the OC Key device that allows quick on-screen overclocking adjustments. Refer to section 2.3.12 OC Key device installation for details. Chapter 2 2-40 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 65
    on the BIOS settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF. • Reset button (2-pin RESET) This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power. ROG RAMPAGE IV EXTREME 2-41
  • Asus RAMPAGE IV EXTREME | User Manual - Page 66
    2.3.1 Additional tools and components to build a PC system 1 bag of screws Philips (cross) screwdriver PC chassis Power supply unit Intel LGA 2011 CPU Intel LGA 2011 compatible CPU Fan DIMM SATA hard disk drive SATA optical disc drive (optional) Graphics card (optional) The tools and
  • Asus RAMPAGE IV EXTREME | User Manual - Page 67
    / closing the double latch. Follow the instructions printed on the metal sealing hatch or the illustrations shown below in this manual. The plastic cap will pop up automatically once the CPU is in place and the hatch properly sealed down. 1A 2 B C 3 4 A B A B ROG RAMPAGE IV EXTREME 2-43
  • Asus RAMPAGE IV EXTREME | User Manual - Page 68
    5 6 Chapter 2 7 8 B A 9B A 2-44 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 69
    2.3.3 CPU heatsink and fan assembly installation Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan if necessary. To install the CPU heatsink and fan assembly 1 A 2 B B A Chapter 2 ROG RAMPAGE IV EXTREME 2-45
  • Asus RAMPAGE IV EXTREME | User Manual - Page 70
    To replace the LGA2011 CPU pad (X-Socket) 1 2 3 4 Chapter 2 5 2-46 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 71
    2.3.4 1 DIMM installation 2 Chapter 2 3 To remove a DIMM B A ROG RAMPAGE IV EXTREME 2-47
  • Asus RAMPAGE IV EXTREME | User Manual - Page 72
    2.3.5 1 Motherboard installation The diagrams in this section are for reference only. The motherboard layout may vary with models, but the installation steps remain the same. 2 Chapter 2 2-48 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 73
    3 Chapter 2 DO NOT overtighten the screws! Doing so can damage the motherboard. ROG RAMPAGE IV EXTREME 2-49
  • Asus RAMPAGE IV EXTREME | User Manual - Page 74
    2.3.6 1 ATX Power connection 2 OR OR Chapter 2 2-50 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 75
    2.3.7 1 SATA device connection OR 2 OR Chapter 2 ROG RAMPAGE IV EXTREME 2-51
  • Asus RAMPAGE IV EXTREME | User Manual - Page 76
    2.3.8 Front I/O Connector To install ASUS Q-Connector 1 2 IDE_LED+ IDE_LED- IDE_LED PWR Ground Reset Ground POWER SW RESET SW To install USB 2.0 Connector To install front panel audio connector Chapter 2 USB 2.0 To install USB 3.0 Connector USB 3.0 2-52 AAFP Chapter 2: Hardware
  • Asus RAMPAGE IV EXTREME | User Manual - Page 77
    2.3.9 Expansion Card installation To install PCIe x16 cards To install PCIe x1 cards Chapter 2 ROG RAMPAGE IV EXTREME 2-53
  • Asus RAMPAGE IV EXTREME | User Manual - Page 78
    PS/2 mouse and keyboard port 2. USB 2.0 ports 7 and 8 3. Bluetooth module 4. LAN (RJ-45) port* 5. External SATA port 2 6. USB 2.0 ports 1 and 2 7. Clear CMOS switch 8. ROG Connect switch 9. USB 2.0 ports 3 to 6 (port 6 is also for ROG Connect) 10. External SATA port 1 11. USB 3.0 ports 1 and 2 12
  • Asus RAMPAGE IV EXTREME | User Manual - Page 79
    the Clear CMOS switch to clear BIOS setup information only when the system hangs due to overclocking. • DO NOT insert a different connector to the external SATA port. • Due to USB 3.0 controller limitation, USB 3.0 devices can only be used under Windows® OS environment and after the USB 3.0 driver
  • Asus RAMPAGE IV EXTREME | User Manual - Page 80
    Chapter 2 2.3.11 Audio I/O connections Audio I/O ports Connect to Headphone and Mic Connect to Stereo Speakers Connect to 2.1 channel Speakers 2-56 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 81
    Chapter 2 Connect to 4.1 channel Speakers Connect to 5.1 channel Speakers Connect to 7.1 channel Speakers ROG RAMPAGE IV EXTREME 2-57
  • Asus RAMPAGE IV EXTREME | User Manual - Page 82
    Chapter 2 2.3.12 OC Key device installation The OC Key device allows quick on-screen overclocking adjustments. Follow the instruction below to install the OC Key device to your system. To install the OC Key device 1. Thread the OC Key cable through the opening on the I/O shield until the stopper on
  • Asus RAMPAGE IV EXTREME | User Manual - Page 83
    CD CPU VTT CPU TEMP 1.49614(V) 1.10802(V) 38(C) OSD TWEAKIT OSD MONITOR SETTING 3. Use the , , and to move the highlighted item, use the key to enter an item, use the key to exit an item, and use the key to save settings. ROG RAMPAGE IV EXTREME
  • Asus RAMPAGE IV EXTREME | User Manual - Page 84
    the rear panel of the motherboard. Launch the firmware upgrade program downloaded from ASUS official website and follow screen intructions to update the OC Key device firmware. • The OC Key function supports PS/2 keyboards and USB keyboards without built-in USB hub only. 2-60 Chapter 2: Hardware
  • Asus RAMPAGE IV EXTREME | User Manual - Page 85
    Description VGA detected Quick boot set to disabled No keyboard detected No memory detected No VGA detected Hardware component failure 7. At power on, hold down the key to enter the BIOS Setup. Follow the instructions in Chapter 3. 2.5 Turning off the computer While the system is ON
  • Asus RAMPAGE IV EXTREME | User Manual - Page 86
    Chapter 2 2-62 Chapter 2: Hardware information
  • Asus RAMPAGE IV EXTREME | User Manual - Page 87
    the system fails to boot after changing any BIOS setting, try to clear the CMOS and reset the motherboard to the default value. �S�e�e��s�e��c�ti�o�n� 2.3.10 Rear Panel connection for information on how to erase the RTC RAM. • The BIOS setup program does not support the bluetooth devices. The BIOS
  • Asus RAMPAGE IV EXTREME | User Manual - Page 88
    : Extreme Tweaker Main Advanced For changing the overclocking settings For changing the basic system configuration For changing the advanced system settings Monitor For displaying the system temperature, power status, and changing the fan settings. Boot Tool Exit For changing the system boot
  • Asus RAMPAGE IV EXTREME | User Manual - Page 89
    Boot, Tool, and Exit) on the menu bar have their respective menu items. Back button This button appears when entering a submenu. Press or use the USB window Select a menu item and press to display a pop-up window the BIOS setup list of options. Chapter 3 ROG RAMPAGE IV EXTREME 3-3
  • Asus RAMPAGE IV EXTREME | User Manual - Page 90
    available Displays the CPU/motherboard temperature, CPU/5V/3.3V/12V voltage output, CPU/ Chassis/CPU_OPT fan speed Exits the BIOS setup program without saving the changes, saves the changes and resets the system, or enters the Advanced Mode Chapter 3 Selects the boot device priority Power Saving
  • Asus RAMPAGE IV EXTREME | User Manual - Page 91
    of the Extreme Tweaker menu items. Incorrect field values can cause the system to malfunction. The configuration options for this section vary depending on the CPU and DIMM model you installed on the motherboard. Scroll down to display the following items: Chapter 3 ROG RAMPAGE IV EXTREME 3-5
  • Asus RAMPAGE IV EXTREME | User Manual - Page 92
    options: [Auto] [100MHz] [125MHz] [166MHz] [250MHz] ClockGen Full Reset [Enabled] [Enabled] Enabled for better overclocking. [Disabled] To skip system shutdown at BCLK frequency adjustment. Turbo Ratio [Auto] Allows you to manually adjust the Trubo CPU ratio. [Auto] All Turbo ratio are set by
  • Asus RAMPAGE IV EXTREME | User Manual - Page 93
    single Turbo Ratio in OS. Partial unlocked CPU: Maximum supported Turbo Ratio will depend on numbers of keyboard and press the key. Changing the values in this menu may cause the system to become unstable! If this happens, revert to the default settings. Chapter 3 ROG RAMPAGE IV EXTREME
  • Asus RAMPAGE IV EXTREME | User Manual - Page 94
    Clock] DRAM RAS# PRE Time [Auto] Configuration options: [Auto] [4 DRAM Clock] - [15 DRAM Clock] DRAM RAS# ACT Time [Auto] Configuration options: [Auto] [4 DRAM Clock] - [40 DRAM Clock] DRAM COMMAND Mode [Auto] Configuration options: [Auto] [1 DRAM Clock] [2 DRAM Clock] [3 DRAM Clock] 3-8 Chapter
  • Asus RAMPAGE IV EXTREME | User Manual - Page 95
    ] [0 DRAM Clock] - [7 DRAM Clock] tWRDD [Auto] Configuration options: [Auto] [0 DRAM Clock] - [7 DRAM Clock] tRWSR [Auto] Configuration options: [Auto] [0 DRAM Clock] - [15 DRAM Clock] Chapter 3 ROG RAMPAGE IV EXTREME 3-9
  • Asus RAMPAGE IV EXTREME | User Manual - Page 96
    Clock] DIGI+ Power Control Do not remove the thermal module while changing the DIGI+ Power Control related parameters . The thermal conditions should be monitored. Chapter 3 3-10 Chapter 3: BIOS setup
  • Asus RAMPAGE IV EXTREME | User Manual - Page 97
    light system loading to increase VRM efficiency [Standard] Proceeds phase control depending on the CPU loading. [Optimized] Loads the ASUS optimized phase tuning profile. [Extreme] Proceeds the full phase mode. [Manual Adjustment] Allows manual adjustment. Chapter 3 ROG RAMPAGE IV
  • Asus RAMPAGE IV EXTREME | User Manual - Page 98
    Bootup Voltage [Auto] This item controls the voltage for CPU at initial boot. Set higher value for better overclockability. T��h�e��v�a�l�u�e�s��r�a�n�g�e��f�ro��m��0�.�8�0�0��V��to��1�.�9�9��0�V��w�i�t�h�a��0�.�0�0�5��V��in�t�e�r�v�a�l�. CPU VSA VCCSA Load-line calibration [Auto] The behavior of
  • Asus RAMPAGE IV EXTREME | User Manual - Page 99
    only when you set the CPU Ratio item to [Auto] and the Turbo Mode item to [Enabled]. Leave this item at [Auto] for best overclocking or set to [Enabled] the and keys to adjust the value. CPU Core Current Limit [Auto] Use the and keys to adjust the value. ROG RAMPAGE IV EXTREME 3-13
  • Asus RAMPAGE IV EXTREME | User Manual - Page 100
    ] to choose a higher voltage to overclock, but doing so might decrease CPU life. Configuration options: [Disabled] [Enabled] BCLK Skew [Auto] Reduce the value to improve BCLK margin. Configuration options: [Auto] [-5] - [+3] CPU VCORE Voltage [Manual Mode] [Manual Mode] Allows you to set a fixed
  • Asus RAMPAGE IV EXTREME | User Manual - Page 101
    ] Allows you to set the CPU PLL voltage. The values range from 1.2500V to 2.5000V with a 0.00625V interval. PCH 1.1v Voltage [Auto] Allows you to set the 1.1v Platform Controller Hub voltage. The values range from 0.8000V to 1.6000V with a 0.00625V interval. Chapter 3 ROG RAMPAGE IV EXTREME 3-15
  • Asus RAMPAGE IV EXTREME | User Manual - Page 102
    control. PCIE Spread Spectrum [Auto] [Auto] Set to auto mode. [Disabled] Enhances the PCIE overclocking ability. [Enabled] Sets to [Enabled] for EMI control. CPU Tweakers' Paradise PCIE Controller Voltage (PEV) [Auto] Configuration options: [-63] - [-1] [Auto] [+1] - [+63] QPI Controller
  • Asus RAMPAGE IV EXTREME | User Manual - Page 103
    range from 0.3950x to 0.6300x with a 0.0050x interval. DRAM Read REF Voltage on CHA/B/C/D The values range from 0.38500x to 0.61500x with a 0.0050x interval. PCH Chipset Tweakers' Paradise ROG RAMPAGE IV EXTREME 3-17
  • Asus RAMPAGE IV EXTREME | User Manual - Page 104
    PCH DMI Skew [Auto] Configuration options: [-96] - [-1] [Auto] [+1] - [+96] PCH USB Skew [Auto] Configuration options: [-96] - [-1] [Auto] [+1] - [+96] PCH SATA3 Strength [ [+96] VGA1/2 PLL Voltage [Auto] Configuration options: [-96] - [-1] [Auto] [+1] - [+96] Chapter 3 3-18 Chapter 3: BIOS setup
  • Asus RAMPAGE IV EXTREME | User Manual - Page 105
    , and security settings. Chapter 3 3.4.1 System Language [English] Allows you to choose the BIOS language version from the options. 3.4.2 System Date [Day xx/xx/xxxx] Allows you to set the system date. 3.4.3 System Time [xx:xx:xx] Allows you to set the system time. ROG RAMPAGE IV EXTREME 3-19
  • Asus RAMPAGE IV EXTREME | User Manual - Page 106
    3.4.4 Security The Security menu items allow you to change the system security settings. Chapter 3 • If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC) RAM to clear the BIOS password. See section 2.3.10 Rear panel connection for information on how to erase the RTC RAM.
  • Asus RAMPAGE IV EXTREME | User Manual - Page 107
    accessing the system. The clear the user password, follow the same steps as in changing a user password, but press when prompted to create/confirm the password. After you clear the password, the User Password item on top of the screen shows Not Installed. Chapter 3 ROG RAMPAGE IV EXTREME
  • Asus RAMPAGE IV EXTREME | User Manual - Page 108
    3.5 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. Chapter 3 3-22 Chapter 3: BIOS setup
  • Asus RAMPAGE IV EXTREME | User Manual - Page 109
    show the CPU-related information that the BIOS automatically detects. The items shown in this screen may be different due to the CPU you installed. to choose the number of CPU cores to activate in each processor package. Configuration options: [All] [1] [2] [3] [4] [5] ROG RAMPAGE IV EXTREME 3-23
  • Asus RAMPAGE IV EXTREME | User Manual - Page 110
    Maximum [Disabled] [Enabled] Allows legacy operating systems to boot even without support for CPUs with extended CPUID functions. [Disabled Technology (EIST). [Disabled] The CPU runs at its default speed. [Enabled] The operating system controls the CPU speed. Turbo Mode [Enabled] [Disabled
  • Asus RAMPAGE IV EXTREME | User Manual - Page 111
    the BIOS automatically detects the presence of SATA devices. The SATA Port items show Not Present if no SATA device is Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance ROG RAMPAGE IV EXTREME 3-25
  • Asus RAMPAGE IV EXTREME | User Manual - Page 112
    (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When read/write of your hard disk errors occur, this feature allows the hard disk to report warning and allow you to enable/disable SATA Hot Plug Support. Configuration options: [Disabled] [Enabled]. Chapter 3 3-26 Chapter
  • Asus RAMPAGE IV EXTREME | User Manual - Page 113
    [Disabled] Disables the function. [Enabled] Enables the support for USB 3.0 devices on legacy operating systems (OS). EHCI Hand-off [Disabled] [Disabled] Disables the function. [Enabled] Enables the support for operating systems without an EHCI hand‑off feature. ROG RAMPAGE IV EXTREME 3-27
  • Asus RAMPAGE IV EXTREME | User Manual - Page 114
    to [HDMI] for HDMI audio output. Bluetooth Controller [Enabled] [Disabled] Disables the controller. [Enabled] Enables the Intel Bluetooth controller. Intel LAN Controller [Enabled] [Disabled] Disables the controller. [Enabled] Enables the Intel LAN controller. 3-28 Chapter 3: BIOS setup
  • Asus RAMPAGE IV EXTREME | User Manual - Page 115
    the motherboard support DVD. ASM1061 Storage OPROM [Enabled] This item appears only when you set the previous item to [IDE Mode] or [AHCI Mode] and allows you to enable or disable the OptionRom of the ASM1061 storage controller. Configuration options: [Disabled] [Enabled] Chapter 3 ROG RAMPAGE IV
  • Asus RAMPAGE IV EXTREME | User Manual - Page 116
    keyboard to turn on the system. Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key] Power On By Mouse [Disabled] [Disabled] Disables the Power On by a mouse. [Enabled] Enables the Power On by a mouse. Power On By PCIE/PCI [Disabled] [Disabled] Disables the PCIE devices system
  • Asus RAMPAGE IV EXTREME | User Manual - Page 117
    ; MB Temperature; PCH Temperature; OPT1/2/3 Temperature[xxxºC/ xxxºF] The onboard hardware monitor automatically detects and displays the CPU, motherboard, and the assigned devices temperatures. Select [Ignored] if you do not wish to display the detected temperatures. ROG RAMPAGE IV EXTREME 3-31
  • Asus RAMPAGE IV EXTREME | User Manual - Page 118
    [xxxxRPM] or [Ignored] / [N/A] The onboard hardware monitor automatically detects and displays the CPU fan, chassis fan, PCH fan, and optional fan speed in rotations per minute (RPM). If any of the fans is not connected to the motherboard, the field shows [N/A]. These items are not user‑configurable
  • Asus RAMPAGE IV EXTREME | User Manual - Page 119
    . The following four items appear only when you set Chassis Fan Profile to [Manual]. Chassis Upper Temperature [70] Use the and keys to adjust the upper limit of the CPU temperature. The values range from 40ºC to 90ºC. Chassis Fan Max. Duty Cycle(%) [100] Use the and keys to adjust
  • Asus RAMPAGE IV EXTREME | User Manual - Page 120
    which the power fan rotates at low speed. Configuration options: [25˚C] [30˚C] [35˚C] [40˚C] OPT FAN 1/2/3 Full Speed Temp [60˚C] Allows you to set the temperature at which the power fan rotates at full speed. Configuration options: [60˚C] [70˚C] [80˚C] [90˚C] Chapter 3 3-34 Chapter 3: BIOS setup
  • Asus RAMPAGE IV EXTREME | User Manual - Page 121
    . Option ROM Messages [Force BIOS] [Force BIOS] The third-party ROM messages will be forced to display during the boot sequence. [Keep Current] The third-party ROM messages will be displayed only if the third-party manufacturer had set the add-on device to do so. ROG RAMPAGE IV EXTREME 3-35
  • Asus RAMPAGE IV EXTREME | User Manual - Page 122
    items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system. • To select the boot device during system startup, press when ASUS Logo appears. • To access Windows OS in
  • Asus RAMPAGE IV EXTREME | User Manual - Page 123
    functions. Select an item then press to display the submenu. Chapter 3 3.8.1 ASUS EZ Flash Utility Allows you to run ASUS EZ Flash Utility. When you press to start the application. For more details, refer to section 3.10.2 ASUS EZ Flash Utility. ROG RAMPAGE IV EXTREME 3-37
  • Asus RAMPAGE IV EXTREME | User Manual - Page 124
    BIOS settings, press , and then select Yes. • DO NOT shut down or reset the system while updating the BIOS to prevent the system boot failure! • We recommend that you update the BIOS file only coming from the same memory/CPU configuration and BIOS version. Chapter 3 3-38 Chapter 3: BIOS
  • Asus RAMPAGE IV EXTREME | User Manual - Page 125
    , system will auto power-on. Forced BIOS2 Boot Allows you to boot the system using BIOS chip 2. COPY BIOS1 to BIOS2 Only current operating BIOS can be mirrored. System will enter the soft-off state. After BIOS backup is finished, system will auto power-on. Chapter 3 ROG RAMPAGE IV EXTREME 3-39
  • Asus RAMPAGE IV EXTREME | User Manual - Page 126
    (CHA, CHB/CHC, CHD); CPU PLL Voltage; VTT CPU Voltage; PCH 1.1v Voltage; PCH 1.5v Voltage; VTTDDR Voltage (CHA, CHB/CHC, CHD); Second VTTCPU Voltage; PCH Logic Reference (1.1VG) Allows you to use the and keys to adjust the values for each item. Refer to 3.3 Extreme Tweaker Menu for details
  • Asus RAMPAGE IV EXTREME | User Manual - Page 127
    Yes to discard changes and exit�. ASUS EZ Mode This option allows you to enter the EZ Mode screen. Launch EFI Shell from filesystem device This option allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of the available filesystem devices. ROG RAMPAGE IV EXTREME 3-41
  • Asus RAMPAGE IV EXTREME | User Manual - Page 128
    version of BIOS, DO NOT manually update the BIOS. Inappropriate BIOS updating may result in the system's failure to boot. Carefully follow the instructions of this chapter to update your BIOS if necessary. Visit the ASUS website (www.asus.com) to download the latest BIOS file for this motherboard
  • Asus RAMPAGE IV EXTREME | User Manual - Page 129
    the BIOS version that you want to download. Click Next. 4. You can decide whether to change the BIOS boot logo, which is the image appearing on screen during the Power‑On Self-Tests (POST). Click Yes if you want to change the boot logo or No to continue. Chapter 3 ROG RAMPAGE IV EXTREME 3-43
  • Asus RAMPAGE IV EXTREME | User Manual - Page 130
    5. Click Browse to locate your desired picture file. 6. Adjust the picture resolution if needed and click Next to continue. Chapter 3 7. Follow the onscreen instructions to complete the update process. 3-44 Chapter 3: BIOS setup
  • Asus RAMPAGE IV EXTREME | User Manual - Page 131
    the update process. Chapter 3 • The screenshots in this section are for reference only. The actual BIOS information vary by models. • Refer to the software manual in the support DVD or visit the ASUS website at www. asus.com for detailed software configuration. ROG RAMPAGE IV EXTREME 3-45
  • Asus RAMPAGE IV EXTREME | User Manual - Page 132
    fo��r�m� the BIOS update process. Reboot the system when the update process is done. • This function can support devices such as a USB flash disk with FAT 32/16 format and single partition only. • DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! Ensure
  • Asus RAMPAGE IV EXTREME | User Manual - Page 133
    you to enter BIOS Setup to recover BIOS setting. To ensure system compatibility and stability, we recommend that you press to load default BIOS values. DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure! Chapter 3 ROG RAMPAGE IV EXTREME 3-47
  • Asus RAMPAGE IV EXTREME | User Manual - Page 134
    hard disk drives (optional). Booting the system in DOS environment 1. Insert the USB flash drive with the latest BIOS file and BIOS Updater to the USB port. 2. Boot your computer. When the ASUS Logo appears, press to show the BIOS Boot Device Select Menu. Insert the support DVD into the optical
  • Asus RAMPAGE IV EXTREME | User Manual - Page 135
    Backing up the current BIOS To backup the current BIOS file using the BIOS Updater Ensure that the USB flash drive is not BIOS Updater for DOS V1.18 [2010/04/29] Current ROM BOARD: RAMPAGE IV EXTREME VER: 0211 DATE: 09/05/2011 PATH: A:\ Update ROM BOARD: Unknown VER: Unknown DATE: Unknown BIOS
  • Asus RAMPAGE IV EXTREME | User Manual - Page 136
    confirm BIOS update. Are you sure to update BIOS? Yes No 4. Select Yes and press . When BIOS update is done, press to exit BIOS Updater. Restart your computer. DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! • For BIOS Updater version 1.04
  • Asus RAMPAGE IV EXTREME | User Manual - Page 137
    the LED stops to blink, then the BIOS flash is completed. • This function can only support devices such as a USB flash disk with FAT32/16 format and single partition. • DO NOT unplug the power of the system while updating the BIOS to prevent system boot failure! Chapter 3 ROG RAMPAGE IV EXTREME
  • Asus RAMPAGE IV EXTREME | User Manual - Page 138
    manual. The Drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to use the devices. The Video menu contains the list of supplementary videos. Click the video titles to watch ROG users' outstanding performances with ROG motherboards
  • Asus RAMPAGE IV EXTREME | User Manual - Page 139
    the Adobe® Acrobat® Reader from the Utilities menu before opening the files. 1. Click on the Manual tab. Click on ASUS Motherboard Utility Guide from the manual list on the left. 2. The Manual folder of the support DVD appears. Double-click the folder of your selected software. 3. Some software
  • Asus RAMPAGE IV EXTREME | User Manual - Page 140
    menu vary with models. • The screeshots of AI Suite II in this user manual are for reference only. The actual screenshots vary with models. • Refer to the software manual in the support DVD or visit the ASUS website at www.asus.com for detailed software configuration. ROG RAMPAGE IV EXTREME 4-3
  • Asus RAMPAGE IV EXTREME | User Manual - Page 141
    4.3.2 TurboV EVO ASUS TurboV EVO introduces TurboV that allows you to manually adjust the CPU frequency and related voltages as well as Auto Tuning function that offers automatic and easy overclocking and system level up. After installing AI Suite II from the motherboard support DVD, launch TurboV
  • Asus RAMPAGE IV EXTREME | User Manual - Page 142
    • Set the CPU Ratio Setting item in BIOS to [Auto] before using the CPU Ratio function in TurboV. Refer to Chapter 3 of your motherboard user manual for details. • The CPU Ratio bars show the status of the CPU cores, which vary with your CPU model. ROG RAMPAGE IV EXTREME 4-5 Chapter 4
  • Asus RAMPAGE IV EXTREME | User Manual - Page 143
    options. • The overclocking result varies with the CPU model and the system configuration. • To prevent overheating from damaging the motherboard, a better thermal environment is strongly recommended. • Fast Tuning: fast CPU overclocking • Extreme Tuning: extreme overclocking for CPU and memory
  • Asus RAMPAGE IV EXTREME | User Manual - Page 144
    the overclocking process. Click Stop if you want to cancel the Overclocking process. 5. TurboV EVO automatically adjusts and saves BIOS settings and restarts the system. After re-entering Windows, a message appears indicating auto tuning success. Click OK to exit. ROG RAMPAGE IV EXTREME 4-7
  • Asus RAMPAGE IV EXTREME | User Manual - Page 145
    Suite II from the motherboard support DVD, launch DIGI+ Power Control by clicking Tool > DIGI+ Power Control on the AI Suite II main menu bar. Select CPU Power and extends the overclocking frequency range simultaneously. CPU Power Phase Control Increase phase number under heavy system loading to get
  • Asus RAMPAGE IV EXTREME | User Manual - Page 146
    response to increase system performance or to slower phase response to increase DRAM power efficiency. • The actual performance boost may vary depending on your CPU specification. • Do not remove the thermal module. The thermal conditions should be monitored. Chapter 4 ROG RAMPAGE IV EXTREME 4-9
  • Asus RAMPAGE IV EXTREME | User Manual - Page 147
    Voltage, and Fan Control. Launching EPU After installing AI Suite II from the motherboard support DVD, launch EPU by clicking Tool > EPU on the AI Suite II main menu bar. Multiple system operating modes Displays the following message if no VGA power saving engine is detected. The items lighting
  • Asus RAMPAGE IV EXTREME | User Manual - Page 148
    , the fan will speed up when the temperature exceeds 70°C. • User: Allows you to configure the CPU fan profile under certain limitations. Refer to the software manual in the support DVD or visit the ASUS website at www.asus.com for detailed software configuration. ROG RAMPAGE IV EXTREME 4-11
  • Asus RAMPAGE IV EXTREME | User Manual - Page 149
    of the three system statuses for certain purposes. Launching Sensor Recorder After installing AI Suite II from the motherboard support DVD, launch Sensor Recorder by clicking Tool > Sensor Recorder on the AI Suite II main menu bar. Using Sensor Recorder Click on Voltage/ Temperature/ Fan Speed tabs
  • Asus RAMPAGE IV EXTREME | User Manual - Page 150
    of any problem with these components. Probe II senses fan rotations, CPU temperature, and system voltages, among others. With this utility, you are assured that your computer is always at a healthy operating condition. Launching Probe II After installing AI Suite II from the motherboard support DVD
  • Asus RAMPAGE IV EXTREME | User Manual - Page 151
    Boost After installing AI Suite II from the motherboard support DVD, launch USB 3.0 Boost by clicking Tool > USB 3.0 Boost on the AI Suite II main menu bar. Configuring USB 3.0 Boost 1. Connect a USB 3.0 device to the USB 3.0 port. 2. USB 3.0 Boost automatically detects the property of the connected
  • Asus RAMPAGE IV EXTREME | User Manual - Page 152
    Version 1.1 (BC 1.1), a USB Implementers Forum (USB-IF) certified USB charging function, is designed to make USB charging faster than the standard USB devices. If your USB device supports the BC 1.1 function*, when you connect your USB device to your system, the system automatically detects your USB
  • Asus RAMPAGE IV EXTREME | User Manual - Page 153
    feature. Launching ASUS Update After installing AI Suite II from the motherboard support DVD, launch ASUS Update by clicking Update> ASUS Update on the AI Suite II main menu bar. Using ASUS Update Select the way you would like to do with the BIOS utility. Click on Next and follow the instructions to
  • Asus RAMPAGE IV EXTREME | User Manual - Page 154
    Select the way you would like to do update your boot logo. Then click Next and follow the given instructions. Change the BIOS boot logo of my motherboard 1. Under Current BIOS, click Browse and choose the desired image for your boot logo. Then click on Next. Chapter 4 ROG RAMPAGE IV EXTREME 4-17
  • Asus RAMPAGE IV EXTREME | User Manual - Page 155
    your computer. Change the boot logo of a downloaded BIOS file and update (or do not update) this BIOS to the motherboard 1. At BIOS File, Browse to download the requested BIOS file to your system. This utility will help you detect the compatibility of the BIOS version. 2. Then at Picture File
  • Asus RAMPAGE IV EXTREME | User Manual - Page 156
    the local PC through your remote PC. Setting up USB connection between your local and remote PC • Install ROG Connect on the remote PC from the provided Support DVD before using ROG Connect. • ROG Connect must buttons to monitor or adjust your local PC. Chapter 4 ROG RAMPAGE IV EXTREME 4-19
  • Asus RAMPAGE IV EXTREME | User Manual - Page 157
    to display more options. RC Poster RC Poster shows the status of the local system during the POST. You can switch the display mode between String and Code. RC Remote RC Remote allows you to operate your local system through the ROG Connect cable. RC Diagram RC Diagram allows you to monitor and
  • Asus RAMPAGE IV EXTREME | User Manual - Page 158
    GPU TweakIt GPU TweakIt allows you to control and monitor the installed GPU on the local system. Use the sliders to adjust the values and click Apply to save your customized settings. Chapter 4 ROG RAMPAGE IV EXTREME 4-21
  • Asus RAMPAGE IV EXTREME | User Manual - Page 159
    ® proprietary UAJ® (Universal Audio Jack) technology for all audio ports, eliminating cable connection errors and giving users plug and play convenience. Follow the installation wizard to install the Realtek® Audio Driver from the support DVD that came with the motherboard package. If the Realtek
  • Asus RAMPAGE IV EXTREME | User Manual - Page 160
    The motherboard supports the Intel® Rapid Storage Technology with RAID 0, RAID 1, RAID 10 and RAID 5 support. • You must install Windows® XP Service Pack 3 or later versions before using Serial ATA hard disk drives. The Serial ATA RAID feature is available only if you are using Windows® XP
  • Asus RAMPAGE IV EXTREME | User Manual - Page 161
    Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ MAIN MENU ] 1. Create RAID Volume 3. Reset Disks to Non-RAID 2. Delete RAID Volume 4. Recovery Volume Options 5. Exit RAID Volumes: None defined. [ DISK/VOLUME INFORMATION Physical Devices: Port Device Model Serial
  • Asus RAMPAGE IV EXTREME | User Manual - Page 162
    the menu options. The RAID BIOS setup screens shown in this section are for reference only and may not exactly match the items on your screen. The utility supports maximum four hard disk drives for the volume. [↑↓]-Prev/Next [SPACE]-SelectDisk [ENTER]-Done Chapter 4 ROG RAMPAGE IV EXTREME 4-25
  • Asus RAMPAGE IV EXTREME | User Manual - Page 163
    4KB to 128KB. The following are typical values: RAID 0: 128KB RAID 10: 64KB RAID 5: 64KB We recommend a lower stripe size for server systems, and a higher stripe size for multimedia computer systems used mainly for audio and video editing. 7. When the Capacity item is selected, enter the RAID volume
  • Asus RAMPAGE IV EXTREME | User Manual - Page 164
    - Option ROM - v10.0.0.1032 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ DELETE VOLUME 298.0GB Normal Yes [ HELP ] Deleting a volume will reset the disks to non-RAID. WARNING: ALL DISK DATA WILL return to the utility main menu. ROG RAMPAGE IV EXTREME 4-27 Chapter 4
  • Asus RAMPAGE IV EXTREME | User Manual - Page 165
    boot device. 4. Insert the support DVD into the optical drive. 5. Save changes and exit BIOS. 6. When the Make Disk menu appears, press to create a RAID driver disk. 7. Insert a formatted floppy disk into the USB floppy disk drive, then press . 8. Follow the succeeding screen instructions
  • Asus RAMPAGE IV EXTREME | User Manual - Page 166
    OS version. Click OK. 4. Follow the succeeding screen instructions to complete the installation. Before loading the RAID driver from a USB flash drive, you have to use another computer to copy the RAID driver from the support DVD to the USB flash drive. Chapter 4 ROG RAMPAGE IV EXTREME 4-29
  • Asus RAMPAGE IV EXTREME | User Manual - Page 167
    steps below: 1. Using another computer, plug the USB floppy disk drive, and insert the floppy disk containing the RAID driver. 2. Right-click My Computer on the Windows® desktop or start menu, and then select Manage from the pop-up window. or 3. Select Device Manager. From the Universal Serial Bus
  • Asus RAMPAGE IV EXTREME | User Manual - Page 168
    ", "usbstor" [HardwareIds.scsi.iaStor_DesktopWorkstationServer] id= "PCI\VEN_8086&DEV_2822&CC_0104","iaStor" id= "USB\VID_03EE&PID_6901", "usbstor" Add the same line to both sections. The VID and PID vary with different vendors. 10. Save and exit the file. ROG RAMPAGE IV EXTREME 4-31 Chapter 4
  • Asus RAMPAGE IV EXTREME | User Manual - Page 169
    Chapter 4 4-32 Chapter 4: Software support
  • Asus RAMPAGE IV EXTREME | User Manual - Page 170
    For Windows XP, go to Control Panel > Add/Remove Programs. For Windows Vista, go to Control Panel > Programs and Features. 3. Select your current graphics card driver/s. 4. For Windows XP, select Add/Remove. For Windows Vista, select Uninstall. 5. Turn off your computer. ROG RAMPAGE IV EXTREME 5-1
  • Asus RAMPAGE IV EXTREME | User Manual - Page 171
    the two graphics card into the PCIEX16 slots. If your motherboard has more than two PCIEX16 slots, refer to Chapter 2 in this user manual for the locations of the PCIEX16 slots recommended for multi- or a DVI cable to the graphics card. goldfingers 5-2 Chapter 5: Multiple GPU technology support
  • Asus RAMPAGE IV EXTREME | User Manual - Page 172
    Control Center window, click Graphics Settings > Performance > AMD CrossFireXTM Configuration. 2. From the Graphics Adapter list, select the graphics card to act as the display GPU. 3. Select Enable CrossFireXTM. 4. Click Apply, and then click OK to exit the window. 1 ROG RAMPAGE IV EXTREME
  • Asus RAMPAGE IV EXTREME | User Manual - Page 173
    fans for better thermal environment. • Visit the NVIDIA zone website (http://www.nzone.com) for the latest certified graphics card and supported 3D application list. 5.2.2 Installing two SLI-ready graphics cards The following pictures are for reference only. The graphics cards and the motherboard
  • Asus RAMPAGE IV EXTREME | User Manual - Page 174
    ™ operating system. Launching the NVIDIA Control Panel You can launch the NVIDIA Control Panel by the following two methods. A. Right click on the empty space of the Windows® desktop and select NVIDIA Control Panel. The NVIDIA Control Panel window appears (See Step B5). ROG RAMPAGE IV EXTREME 5-5
  • Asus RAMPAGE IV EXTREME | User Manual - Page 175
    Chapter 5 B1. If you cannot see the NVIDIA Control Panel item in step (A), select Personalize. B2. From the Personalization window, select Display Settings. B3. From the Display Settings dialog box, click Advanced Settings. 5-6 Chapter 5: Multiple GPU technology support
  • Asus RAMPAGE IV EXTREME | User Manual - Page 176
    the NVIDIA Control Panel. Chapter 5 B5. The NVIDIA Control Panel window appears. Enabling SLI settings From the NVIDIA Control Panel window, select Set SLI Configuration. Click Enable SLI and set the display for viewing SLI rendered content. When done, click Apply. ROG RAMPAGE IV EXTREME 5-7
  • Asus RAMPAGE IV EXTREME | User Manual - Page 177
    Chapter 5 5-8 Chapter 5: Multiple GPU technology support
  • Asus RAMPAGE IV EXTREME | User Manual - Page 178
    Fax +49-2102-959911 Web site www.asus.de Online contact www.asus.de/sales Technical Support Telephone (Component) Telephone (System/Note/Eee/LCD) Support Fax Online support +49-1805-010923* +49-1805-010920* +49-2102-9599-11 support.asus.com * EUR 0.14/minute from a German
  • Asus RAMPAGE IV EXTREME | User Manual - Page 179
    conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference ASUS COMPUTER GmbH Address, City: HARKORT STR. 21-23, 40880 RATINGEN Country: GERMANY declare the following apparatus: Product name : Motherboard Model name : RAMPAGE IV EXTREME
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
Motherboard
RAMPAGE IV
EXTREME