Asus TUEP2-M TUEP2-M User Manual - Page 43

Starting Up the First Time

Get Asus TUEP2-M PDF manuals and user guides View all Asus TUEP2-M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

3. H/W SETUP Powering Up 3. HARDWARE SETUP 3.9 Starting Up the First Time 1. After all connections are made, close the system case cover. 2. Be sure that all switches are off (in some systems, marked with ), and the power input voltage is set to comply with the standard used in your country (220V-240V or 110-120V). 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. 4. Connect the power cord into a power outlet that is equipped with a surge protector. 5. You may then turn on your devices in the following order: a. Your monitor b. External SCSI devices (starting with the last device on the chain) c. Your system power. For ATX power supplies, you need to switch on the power supply as well as press the ATX power switch on the front of the case. 6. The power LED on the front panel of the system case will light. For ATX power supplies, the system LED will light when the ATX power switch is pressed. The LED on the monitor may light up or switch between orange and green after the system's if it complies with "green" standards or if it has a power standby feature. The system will then run power-on tests. While the tests are running, the BIOS will alarm beeps or additional messages will appear on the screen. If you do not see anything within 30 seconds from the time you turn on the power, the system may have failed a power-on test. Recheck your jumper settings and connections or call your retailer for assistance. Award BIOS Beep Codes Beep One short beep when displaying logo Long beeps in an endless loop One long beep followed by three short beeps High frequency beeps when system is working Meaning No error during POST No DRAM installed or detected Video card not found or video card memory bad CPU overheated System running at a lower frequency ASUS TUEP2-M User's Manual 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
43
3. HARDWARE SETUP
ASUS TUEP2-M User’s Manual
Powering Up
3. H/W SETUP
3.9
Starting Up the First Time
1.
After all connections are made, close the system case cover.
2.
Be sure that all switches are off (in some systems, marked with
), and
the power input voltage is set to comply with the standard used in your
country (220V-240V or 110-120V).
3.
Connect the power supply cord into the power supply located on the
back of your system case according to your system user’s manual.
4.
Connect the power cord into a power outlet that is equipped with a surge
protector.
5.
You may then turn on your devices in the following order:
a.
Your monitor
b.
External SCSI devices (starting with the last device on the chain)
c.
Your system power. For ATX power supplies, you need to switch on
the power supply as well as press the ATX power switch on the front
of the case.
6.
The power LED on the front panel of the system case will light. For
ATX power supplies, the system LED will light when the ATX power
switch is pressed. The LED on the monitor may light up or switch between
orange and green after the system’s if it complies with “green” standards
or if it has a power standby feature. The system will then run power-on
tests. While the tests are running, the BIOS will alarm beeps or additional
messages will appear on the screen. If you do not see anything within 30
seconds from the time you turn on the power, the system may have failed
a power-on test. Recheck your jumper settings and connections or call
your retailer for assistance.
Award BIOS Beep Codes
Beep
Meaning
One short beep when
No error during POST
displaying logo
Long beeps in an endless loop
No DRAM installed or detected
One long beep followed by
Video card not found or video card
three short beeps
memory bad
High frequency beeps when
CPU overheated
system is working
System running at a lower frequency