Asus V2-AE1 User Guide - Page 34

Hard disk drive

Get Asus V2-AE1 PDF manuals and user guides View all Asus V2-AE1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

2.7.3 Hard disk drive The system supports a 3.5" IDE or SATA hard disk drive. To install a hard disk drive: 1. Place the chassis upright, then remove the upper 3.5" drive bay metal plate cover. 2. Insert the hard disk drive to the bay, then carefully push the drive until its screw holes align with the holes on the bay. 3. Secure the hard disk drive with two screws on both sides of the bay. 3 3 2 4. F o r S A T A H D D: Connect the SATA signal and power plugs to the connectors at the back of the drive. Some Serial ATA HDDs have two power connectors (legacy 4-pin and SATA power 15-pin). Depending on the available power supply plugs, use o n l y o n e of the power connectors. Connecting a power plug on both connectors could damage the drive. For IDE HDD: Connect the IDE and power plugs to the connectors at the back of the drive. SATA IDE 5. F o r S A T A H D D: Connect the other end of the Serial ATA cable to a SATA connector on the motherboard. See page 4-7 for the location of the Serial ATA connectors. For IDE HDD: Connect the other end of IDE cable to the connector (labeled PRI_IDE) on the motherboard. See page 4-6 for the location of the IDE connectors. 2-18 Chapter 2: Basic installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
2-18
2-18
2-18
2-18
2-18
Chapter 2: Basic installation
Chapter 2: Basic installation
Chapter 2: Basic installation
Chapter 2: Basic installation
Chapter 2: Basic installation
2.7.3
2.7.3
2.7.3
2.7.3
2.7.3
Hard disk drive
Hard disk drive
Hard disk drive
Hard disk drive
Hard disk drive
The system supports a 3.5” IDE or SATA hard disk drive.
To install a hard disk drive:
1.
Place the chassis upright, then remove the upper 3.5” drive bay metal
plate cover.
2.
Insert the hard disk drive to the bay, then carefully push the drive
until its screw holes align with the holes on the bay.
3.
Secure the hard disk drive with two screws on both sides of the bay.
4.
For SATA HDD
For SATA HDD
For SATA HDD
For SATA HDD
For SATA HDD: Connect the SATA signal and power plugs to the
connectors at the back of the drive.
Some Serial ATA HDDs have two power connectors (legacy 4-pin and
SATA power 15-pin). Depending on the available power supply plugs, use
only one
only one
only one
only one
only one of the power connectors. Connecting a power plug on both
connectors could damage the drive.
For IDE HDD
For IDE HDD
For IDE HDD
For IDE HDD
For IDE HDD: Connect the IDE and power plugs to the connectors at the
back of the drive.
SATA
SATA
SATA
SATA
SATA
IDE
IDE
IDE
IDE
IDE
5.
For SATA HDD
For SATA HDD
For SATA HDD
For SATA HDD
For SATA HDD: Connect the other end of the Serial ATA cable to a
SATA connector on the motherboard. See page 4-7 for the location of
the Serial ATA connectors.
For IDE HDD
For IDE HDD
For IDE HDD
For IDE HDD
For IDE HDD: Connect the other end of IDE cable to the connector
(labeled PRI_IDE) on the motherboard. See page 4-6 for the location
of the IDE connectors.
3
3
2