Asus V3-M2V890 V3-M2V890 English Edition User's Manual - Page 35

If you install two IDE hard disk drives, connect the black interface

Get Asus V3-M2V890 PDF manuals and user guides View all Asus V3-M2V890 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

To install an IDE hard disk drive: 1. Follow steps 1-4 of the previous section. 2. Connect the blue interface of the IDE ribbon cable to the primary IDE connector (blue connector labeled PRI_IDE) on the motherboard. See page 4-6 for the location of the connector. IDE ribbon cable Power cable • If you will install only one hard disk drive, make sure to configure your hard disk drive as Master device before connecting the IDE cable and power plug. Refer to the HDD documentation on how to set the drive as a Master device. • If you will install two IDE hard disk drives, configure the other device as Slave. 3. Connect the gray interface of the IDE ribbon cable to the IDE connector on the drive. 4. If you install two IDE hard disk drives, connect the black interface of the IDE ribbon cable to the IDE connector on the second (Slave) IDE hard disk drive. 5. Connect a 4-pin power plug from the power supply unit to the power connector at the back of the drive(s). ASUS V-Series M2V890 2-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
2-17
ASUS V-Series M2V890
To install an IDE hard disk drive:
1.
Follow steps 1-4 of the previous section.
2.
Connect the blue interface of the IDE ribbon cable to the primary IDE
connector (blue connector labeled PRI_IDE) on the motherboard. See
page 4-6 for the location of the connector.
•
If you will install only one hard disk drive, make sure to configure
your hard disk drive as Master device before connecting the IDE
cable and power plug. Refer to the HDD documentation on how to
set the drive as a Master device.
•
If you will install two IDE hard disk drives, configure the other device
as Slave.
3.
Connect the gray interface of the IDE ribbon cable to the IDE
connector on the drive.
4.
If you install two IDE hard disk drives, connect the black interface of
the IDE ribbon cable to the IDE connector on the second (Slave) IDE
hard disk drive.
5.
Connect a 4-pin power plug from the power supply unit to the power
connector at the back of the drive(s).
IDE ribbon cable
Power cable