Asus V3-M2V890 V3-M2V890 English Edition User's Manual - Page 36

Installing a floppy disk drive - barebone

Get Asus V3-M2V890 PDF manuals and user guides View all Asus V3-M2V890 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

2.9 Installing a floppy disk drive The V-Series M2V890 Barebone system comes with one 3.25-inch drive bay for a floppy disk drive. To install a floppy disk drive: 1. Remove the front panel cover. For instructions on how to remove the front panel cover, refer to page 2-3 of section "2.3 Removing the side cover and front panel assembly". 2. Carefully insert the floppy disk drive into the floppy drive bay until the screw holes align with the holes on the bay. 3. Secure the floppy disk drive with two screws on both sides. 3 3 2 4. Connect the floppy disk drive signal cable to the signal connector at the back of the drive. Power cable Floppy ribbon cable 5. Connect the other end of the signal cable to the floppy disk drive connector on the motherboard. See page 4-4 for the location of the floppy disk drive connector. 6. Connect a 4-pin power cable from the power supply unit to the power connector at the back of the floppy disk drive. 2-18 Chapter 2: Basic installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
2-18
Chapter 2: Basic installation
2.9
Installing a floppy disk drive
The V-Series M2V890 Barebone system comes with one 3.25-inch drive
bay for a floppy disk drive.
To install a floppy disk drive:
1.
Remove the front panel cover.
For instructions on how to remove the front panel cover, refer to page
2-3 of section “2.3 Removing the side cover and front panel assembly”.
2.
Carefully insert the floppy disk drive into the floppy drive bay until the
screw holes align with the holes on the bay.
3.
Secure the floppy disk drive with two screws on both sides.
4.
Connect the floppy disk drive signal cable to the signal connector at
the back of the drive.
3
3
2
5.
Connect the other end of the signal cable to the floppy disk drive
connector on the motherboard. See page 4-4 for the location of the
floppy disk drive connector.
6.
Connect a 4-pin power cable from the power supply unit to the power
connector at the back of the floppy disk drive.
Floppy ribbon
cable
Power cable