Asus V3-M2V890 V3-M2V890 English Edition User's Manual - Page 76

ECC Configuration

Get Asus V3-M2V890 PDF manuals and user guides View all Asus V3-M2V890 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

MCT Timing Mode [Auto] Appears only when the Parallel Port Mode is set to [ECP]. This item allows you to set the Parallel Port ECP DMA. Configuration options: [DMA0] [DMA1] [DMA3] Bank Interleacving [Auto] Sets whether to allow memory accesses to be spread out over BANKS on the same node or across nodes, decreasing access contention. Configuration options: [Disabled] [Enabled] Enable Clock to All DIMMs [Disabled] Allows you to enable or disable clock to all DIMMs. Configuration options: [Disabled] [Enabled] MemClk Tristate C3/ATLVID [Disabled] Allows you to enable or disable the MemCLK Tri-Stating During C3 and Alt VID. Configuration options: [Disabled] [Enabled] Memory Hole Remapping [Disabled] Allows you to enable or disable Memory Remapping around the memory hole. Configuration options: [Disabled] [Enabled] ECC Configuration ECC Configuration DRAM ECC Enable 4-Bit ECC Mode DRAM SCRUB REDIRECT DRAM BG Srub [Enabled] [Disabled] [Disabled] [Disabled] DRAM ECC Enable [Disabled] Enables or disables the DRAM ECC that allows hardware to report and correct memory errors automatically to maintain system integrity. Configuration options: [Disabled] [Enabled] The following item appears only when the DRAM ECC item is set to [Enabled]. 5-18 Chapter 5: BIOS setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
5-18
Chapter 5: BIOS setup
ECC Configuration
DRAM ECC Enable
[Enabled]
4-Bit ECC Mode
[Disabled]
DRAM SCRUB REDIRECT
[Disabled]
DRAM BG Srub
[Disabled]
ECC Configuration
DRAM ECC Enable [Disabled]
Enables or disables the DRAM ECC that allows hardware to report and
correct memory errors automatically to maintain system integrity.
Configuration options: [Disabled] [Enabled]
The following item appears only when the
DRAM ECC
item is set to [Enabled].
MCT Timing Mode [Auto]
Appears only when the Parallel Port Mode is set to [ECP]. This item
allows you to set the Parallel Port ECP DMA.
Configuration options: [DMA0] [DMA1] [DMA3]
Bank Interleacving [Auto]
Sets whether to allow memory accesses to be spread out over BANKS
on the same node or across nodes, decreasing access contention.
Configuration options: [Disabled] [Enabled]
Enable Clock to All DIMMs [Disabled]
Allows you to enable or disable clock to all DIMMs.
Configuration options: [Disabled] [Enabled]
MemClk Tristate C3/ATLVID [Disabled]
Allows you to enable or disable the MemCLK Tri-Stating During C3 and
Alt VID. Configuration options: [Disabled] [Enabled]
Memory Hole Remapping [Disabled]
Allows you to enable or disable Memory Remapping around the memory
hole. Configuration options: [Disabled] [Enabled]