Behringer UB-Xa User Manual - Page 13

13 UB-Xa User Manual g - Sostenuto - pressing the pedal while holding notes on the keyboard causes the Pedal Release time set by Shift & Control 48 to be activated. Releasing the pedal reverts to the Release Time set by Control 48. 8. Hold Action - switches between Negative (default) where pressing the footswitch causes the selected action to take place; Positive where the selected action takes place until the footswitch is pressed and Disabled. 9. Hold Latch - switches between Unlatched (default) where releasing the footswitch causes the selected action to stop and Latched where the selected action will continue until the footswitch is pressed again. 10. Vibrato Assign - allows the vibrato footpedal input (Back Panel 88 below) to be reassigned. Options are: a - Filter - the footpedal will control the filter cutoff frequency, with a range between the current filter frequency setting set by control 32 and the filter being fully opened. b - Vibrato (default) - the footpedal will control the amount of vibrato from the performance section LFO to whichever destinations have been selected with buttons 76 & 77. The modulation lever 74 will still be active. c - Attack - the footpedal will alter the loudness Attack time, overriding control 45, to the maximum of 14 seconds. d - Release - the footpedal will alter the loudness Release time, overriding control 48, to the maximum of 20 seconds e - Decay - the footpedal will alter the loudness Decay time, overriding control 46, to the maximum of 10 seconds. f - General 1 CC16 - the footpedal will affect continuous controller #16, which can be assigned through the Modulation Matrices. g - General 2 CC17 - the footpedal will affect continuous controller #17, which can be assigned through the Modulation Matrices. h - General 3 CC18 - the footpedal will affect continuous controller #18, which can be assigned through the Modulation Matrices. i - General 4 CC19 - the footpedal will affect continuous controller #19, which can be assigned through the Modulation Matrices. 11. Vibrato Action - switches between Negative (default) where pressing the footpedal decreases the effect; Positive where the footpedal action increases the effect and Disabled. 12. Vibrato Trim L - allows trimming of the vibrato pedal effect in the left channel. Continuously variable between 0 (default) and 255. 13. Vibrato Trim R - allows trimming of the vibrato pedal effect in the Right channel. Continuously variable between 0 and 255 (default). 14. Filter Assign - allows the filter footpedal input (Back Panel 89 below) to be reassigned. Options are: a - Filter (default) - the footpedal will control the filter cutoff frequency, with a range between the current filter frequency setting set by control 32 and the filter being fully opened. b - Vibrato - the footpedal will control the amount of vibrato from the performance section LFO to whichever destinations have been selected with buttons 76 & 77. The modulation lever 74 will still be active. c - Attack - the footpedal will alter the loudness Attack time, overriding control 45, to the maximum of 14 seconds. d - Release - the footpedal will alter the loudness Release time, overriding control 48, to the maximum of 20 seconds. e - Decay - the footpedal will alter the loudness Decay time, overriding control 46, to the maximum of 10 seconds f - General 1 CC16 - the footpedal will affect continuous controller #16, which can be assigned through the Modulation Matrices. g - General 2 CC17 - the footpedal will affect continuous controller #17, which can be assigned through the Modulation Matrices. h - General 3 CC18 - the footpedal will affect continuous controller #18, which can be assigned through the Modulation Matrices. i - General 4 CC19 - the footpedal will affect continuous controller #19, which can be assigned through the Modulation Matrices. 15. Filter Action - switches between Negative (default) where pressing the footpedal decreases the effect; Positive; where the footpedal action increases the effect and Disabled. 16. Filter Trim L - allows trimming of the filter pedal effect in the left channel. Continuously variable between 0 (default) and 255. 17. Filter Trim R - allows trimming of the filter pedal effect in the Right channel. Continuously variable between 0 and 255 (default). Sysex Data Dump Controls transmission of System Exclusive data relating to the following areas: a - Upper Patch - the patch being played by the upper keyboard in Split or Double mode, or the current patch otherwise. b - Lower Patch - the patch being played by the lower keyboard in Split or Double mode. c - Current Program - the current program settings (pointer to upper and lower patch, keyboard split point). d - Bank A / B / C / D - the content of the required patch bank. e - Globals - contents of the Global Settings menu. f - Split Double - the content of the Split and Double program memories. g - Tuning 1-8 - the tuning settings of voices 1-8 (only required for support). h - Tuning 9-16 - the tuning setting of voices 9-16 (only required for support). i - Current Atrophy - the Atrophy settings of the current patch. j - Profiles - all of the Atrophy Profiles stored on your UB-Xa. Factory Defaults Selectively erases stored data and replaces it with the defaults that the UB-Xa is shipped with. You can select from: a - Banks A - D Reset b - Split/Double Programs Reset c - Settings Reset d - Atrophy Reset e - Full Reset It is suggested that care should be taken when using this option, as wipes cannot be reversed. You will be prompted to cancel or confirm before the wipe takes place. Recover Last Allows the last patch edited to be recovered, with edits, if the user accidentally navigates away without writing. Main Firmware Shows the current Firmware version. Firmware updates are available from Behringer.com and can be installed with the SYNTHTRIBE app for Windows or Mac. It is recommended that you keep your UB-Xa Firmware up to date in order to access new features.