BenQ LX60ST Laser DLP Projector LX60ST and LW61ST User Manual - Page 21

Adjusting the projected image, Auto-adjusting the image, Fine-tuning the image clarity

Get BenQ LX60ST Laser DLP Projector PDF manuals and user guides View all BenQ LX60ST Laser DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Adjusting the projected image Adjusting the projection angle The projector is equipped 2 adjuster feet. These adjusters change the image height and projection angle. To adjust the projector: Screw the adjuster feet to fine-tune the horizontal angle. To retract the feet, screw the adjuster feet in a reverse direction. If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 22 for details. Do not look into the lens while the light source is on. The strong light from the light source may cause damage to your eyes. Be careful when you press the quickrelease button as it is close to the exhaust vent where hot air comes from. Auto-adjusting the image In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality. The current source information will be displayed in the corner of the screen for 3 seconds. This function is only available when PC signal (analog RGB) is selected. Fine-tuning the image clarity Sharpen the image by rotating the focus ring. Operation 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Operation
21
Adjusting the projected image
Adjusting the projection angle
The projector is equipped 2 adjuster feet. These adjusters change the image height and
projection angle. To adjust the projector:
Screw the adjuster feet to fine-tune the
horizontal angle.
To retract the feet, screw the adjuster feet in a
reverse direction.
If the projector is not placed on a flat surface or
the screen and the projector are not
perpendicular to each other, the projected
image becomes trapezoidal. To correct this
situation, see
"Correcting keystone" on page 22
for details.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press
AUTO
on
the projector or remote control. Within 3 seconds, the built-in Intelligent Auto
Adjustment function will re-adjust the values of Frequency and Clock to provide the best
picture quality.
The current source information will be displayed in the corner of the screen for 3 seconds.
This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image clarity
Sharpen the image by rotating the focus ring.
Do not look into the lens while the
light source is on. The strong light
from the light source may cause
damage to your eyes.
Be careful when you press the quick-
release button as it is close to the
exhaust vent where hot air comes
from.