BenQ LX60ST Laser DLP Projector LX60ST and LW61ST User Manual - Page 52

Troubleshooting

Get BenQ LX60ST Laser DLP Projector PDF manuals and user guides View all BenQ LX60ST Laser DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Plug the power cord into the AC power jack on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. No picture Cause Remedy The video source is not turned on or connected correctly. The projector is not correctly connected to the input signal device. The input signal has not been correctly selected. The lens cover is still closed. Turn the video source on and check that the signal cable is connected correctly. Check the connection. Select the correct input signal with the SOURCE key on the projector or remote control. Open the lens cover. Blurred image Cause The projection lens is not correctly focused. The projector and the screen are not aligned properly. The lens cover is still closed. Remedy Adjust the focus of the lens using the focus ring. Adjust the projection angle and direction as well as the height of the projector if necessary. Open the lens cover. Remote control does not work Cause Remedy The batteries are out of power. There is an obstacle between the remote control and the projector. You are too far away from the projector. Replace the batteries with new ones. Remove the obstacle. Stand within 8 meters (26 feet) of the projector. The password is incorrect Cause You do not remember the password. Remedy Please see "Entering the password recall procedure" on page 25 for details. 52 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Troubleshooting
52
Troubleshooting
The projector does not turn on.
No picture
Blurred image
Remote control does not work
The password is incorrect
Cause
Remedy
There is no power from the power cord.
Plug the power cord into the AC power jack on
the projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the signal
cable is connected correctly.
The projector is not correctly connected
to the input signal device.
Check the connection.
The input signal has not been correctly
selected.
Select the correct input signal with the
SOURCE
key on the projector or remote control.
The lens cover is still closed.
Open the lens cover.
Cause
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as well
as the height of the projector if necessary.
The lens cover is still closed.
Open the lens cover.
Cause
Remedy
The batteries are out of power.
Replace the batteries with new ones.
There is an obstacle between the remote
control and the projector.
Remove the obstacle.
You are too far away from the projector.
Stand within 8 meters (26 feet) of the projector.
Cause
Remedy
You do not remember the password.
Please see
"Entering the password recall
procedure" on page 25
for details.