BenQ MX813ST Short-Throw DLP Projector User Manual - Page 25

Operation, Starting up the projector

Get BenQ MX813ST Short-Throw DLP Projector PDF manuals and user guides View all BenQ MX813ST Short-Throw DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Operation Starting up the projector 1. Plug the power cord into the projector and into a power outlet. Check that the POWER indicator light on the projector lights orange after power has been applied. • Please use the original accessories (e.g. power cable) only with the device to avoid possible dangers such as electric shock and fire. • If Direct power on function is activated in the SYSTEM SETUP: Basic > Operation Settings menu, the projector will turn on automatically after the power cord has been connected and power has been applied. See "Direct Power On" on page 48 for details. 2. Remove the lens cap. If it is closed, it could become deformed due to the heat produced by the projection lamp. 3. Press II Power on the projector or ON on the remote control to start the projector. The POWER indicator light flashes and stays green when the projector is on. The start up procedure takes about 10-20 seconds. In the later stage of start up, a startup logo is projected. (If necessary) Use the focus ring/focus slide lever to adjust the image clearness. If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp. 4. If the projector is activated for the first time, select your OSD language following the onscreen instructions. 5. If you are prompted for a password, press the arrow keys to enter a six digit password. See "Utilizing the password function" on page 29 for details. 6. Switch all of the connected equipment on. 7. The projector will start to search for input signals. The current input signal being scanned displays in the screen. If the projector doesn't detect a valid signal, the message 'No Signal' will continue displaying until an input signal is found. Operation 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Operation
25
Operation
Starting up the projector
1.
Plug the power cord into the projector and into
a power outlet. Check that the
POWER
indicator light
on the projector lights orange
after power has been applied.
•
Please use the original accessories (e.g. power cable)
only with the device to avoid possible dangers such as
electric shock and fire.
•
If Direct power on function is activated in the
SYSTEM SETUP: Basic > Operation Settings menu, the projector will turn on automatically
after the power cord has been connected and power has been applied. See
"Direct Power
On" on page 48
for details.
2.
Remove the lens cap. If it is closed, it could
become deformed due to the heat produced
by the projection lamp.
3.
Press
Power
on the projector or
ON
on
the remote control to start the projector. The
POWER indicator light
flashes and stays
green when the projector is on.
The start up procedure takes about 10-20
seconds. In the later stage of start up, a
startup logo is projected.
(If necessary) Use the focus ring/focus slide lever to adjust the image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the lamp.
4.
If the projector is activated for the first time,
select your OSD language following the on-
screen instructions.
5.
If you are prompted for a password, press the
arrow keys to enter a six digit password. See
"Utilizing the password function" on page 29
for details.
6.
Switch all of the connected equipment on.
7.
The projector will start to search for input
signals. The current input signal being scanned
displays in the screen. If the projector doesn't
detect a valid signal, the message '
No Signal
'
will continue displaying until an input signal is
found.
I
I