Home » BenQ Manuals » Projectors » BenQ MX813ST Short-Throw DLP Projector » Manual Viewer

BenQ MX813ST Short-Throw DLP Projector User Manual - Page 49

SYSTEM, SETUP, Advanced, INFORMA, Off/Computer1/Computer2/Video, S

Get BenQ MX813ST Short-Throw DLP Projector PDF manuals and user guides

View all BenQ MX813ST Short-Throw DLP Projector manuals

Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

High Altitude Mode On/Off Yes/No Mute Off/On Audio Settings Volume Power on/off Ring Tone Off/On Lamp Mode Normal/Economic/Smart Eco Lamp Settings Reset lamp timer Reset/Cancel Equivalent lamp hour Change password Security Settings Change Security Power on Lock Settings Splash Screen Lock Baud Rate 2400/4800/9600/14400/19200/ 38400/ 57600/115200 Test Pattern On/Off 5. SYSTEM Closed Caption SETUP: Advanced Standby Settings Closed Caption Enable Caption Version Monitor Out Audio PassThrough Off/On CC1/CC2/CC3/CC4 On/Off Off/Computer1/Computer2/Video,Svideo/HDMI Network On/Off Wired LAN Status DHCP IP Address Subnet Mask Network Settings Default Gateway DNS Server Apply AMX Device Discovery On/Off Mac Address Reset All Settings Reset/Cancel 6. INFORMA Current System Status TION • Source • Picture Mode • Resolution • Color System • Equivalent Lamp Hour • Firmware Version Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible. Operation 49

Section	Page
Important safety instructions	3
Introduction	7
Projector features	7
Shipping contents	8
Standard accessories	8
Optional accessories	8
Projector exterior view	9
Controls and functions	10
Projector	10
1. Power/POWER indicator light	10
2. MENU/EXIT	10
3. Volume/Arrow keys (/Left, / Right)	10
4. MODE/ENTER	10
5. ECO BLANK	10
6. Keystone/Arrow keys (/Up, / Down)	10
7. TEMP indicator light	10
8. LAMP indicator light	10
9. AUTO	10
10. SOURCE	10
Mounting the projector	11
Remote control	12
1. Power	12
2. Freeze	12
3. Menu/Exit	12
4. Left/Right	12
5. Smart Eco	12
6. Eco Blank	12
7. Digital Zoom keys (+, -)	12
8. Volume +/-	12
9. Page Up/Down	12
10. Keystone/Arrow keys (/Up, /Down)	12
11. Auto	12
12. Mode/Enter	12
13. Source	12
14. Timer On	13
15. Timer Setup	13
Positioning your projector	14
Choosing a location	14
1. Front Table	14
2. Front Ceiling	14
3. Rear Table	14
4. Rear Ceiling	14
Obtaining a preferred projected image size	15
How to determine the position of the projector for a given screen size	16
How to determine the recommended screen size for a given distance	16
Projection dimensions	17
Screen size	17
Distance from screen (mm)	17
Vertical offset (mm)	17
Diagonal	17
W	17
(mm)	17
H	17
(mm)	17
Inch	17
mm	17
Connection	18
Connecting a computer or monitor	19
Connecting a computer	19
Connecting a monitor	20
Connecting Video source devices	21
Connecting an HDMI source device	22
Connecting a Component Video source device	23
Connecting an S-Video/composite source device	24
Operation	25
Starting up the projector	25
Adjusting the projected image	26
Adjusting the projection angle	26
Auto-adjusting the image	26
Fine-tuning the image clarity	27
Correcting keystone	27
Using the menus	28
Securing the projector	29
Using a security cable lock	29
Utilizing the password function	29
Setting a password	29
If you forget the password	29
Entering the password recall procedure	30
Changing the password	30
4. Enter a new password.	30
Disabling the password function	30
Switching input signal	31
Magnifying and searching for details	32
Selecting the aspect ratio	32
Optimizing the image	34
Selecting a picture mode	34
Using Wall Color	35
Fine-tuning the image quality in user modes	35
Adjusting Color	35
Creating your own startup screen	37
Setting the presentation timer	38
Remote paging operations	39
Hiding the image	39
Freezing the image	40
Operating in a high altitude environment	40
Adjusting the sound	40
Personalizing the projector menu display	41
Controlling the projector through a LAN environment	42
i. These buttons function the same as the ones on the OSD menus or remote control.	43
ii. To switch input source, click on your desired signal.	43
i. You can name the projector, keep track of its location and the person in charge of it.	44
ii. You can adjust the Wired LAN settings.	44
iii. Once set, access to the remote network operation on this projector has been password-protected.	44
iv. Once set, access to the tools page has been password-protected.	44
v. Press exit to go back to the Crestron remote network operation page.	44
i. Press exit to go back to the Crestron remote network operation page.	45
Shutting down the projector	46
Direct power off	46
Menu operation	47
Menu system	47
Description of each menu	50
Maintenance	59
Care of the projector	59
Cleaning the lens	59
Cleaning the projector case	59
Storing the projector	59
Transporting the projector	59
Lamp information	60
Getting to know the lamp hour	60
Extending lamp life	60
Timing of replacing the lamp	61
Replacing the lamp	62
Indicators	65
Troubleshooting	66
Specifications	67
Dimensions	68
Ceiling mount installation	68
Wall mount installation	69
Minimum Ceiling Height (mm) = f + H + b + 60 + 268.16+ c	70
Timing chart	71
Supported timing for HDMI input	72
Supported timing for Component-YPbPr input	73