BenQ MX813ST Short-Throw DLP Projector User Manual - Page 41

Personalizing the projector menu display

Get BenQ MX813ST Short-Throw DLP Projector PDF manuals and user guides View all BenQ MX813ST Short-Throw DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Adjusting the sound level To adjust the sound level, press Volume+/ Volume- on the remote control, or: 1. Repeat steps 1-2 above. 2. Highlight VOLUME and select a desired sound level. Turning off the Power on/off ring tone To turn off the ring tone: 1. Repeat steps 1-2 in Muting the sound section. 2. Highlight Power on/off Ring Tone and select Off. The only way to change Power on/off ring tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power on/off ring tone. Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • Menu display time in the SYSTEM SETUP: Basic > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame. • Menu position in the SYSTEM SETUP: Basic > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position. • Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to select your language. • Reminder Message in the SYSTEM SETUP: Basic > Menu Settings menu sets whether to display reminder messages on screen. Use / to select your desired setting. • Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen. Operation 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Operation
41
Adjusting the sound level
To adjust the sound level, press
Volume+/
Volume-
on the remote control, or:
1.
Repeat steps 1-2 above.
2.
Highlight
VOLUME
and select a desired
sound level.
Turning off the Power on/off ring tone
To turn off the ring tone:
1.
Repeat steps 1-2 in Muting the sound section.
2.
Highlight
Power on/off Ring Tone
and select
Off
.
The only way to change Power on/off ring tone is setting On or Off here. Setting the sound mute
or changing the sound level will not affect the Power on/off ring tone.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
Menu display time
in the
SYSTEM SETUP: Basic
>
Menu Settings
menu sets
the length of time the OSD will remain active after your last key press. The time length
ranges from 5 to 30 seconds in 5-second increments. Use
/
to select a suitable
time frame.
•
Menu position
in the
SYSTEM SETUP: Basic
>
Menu Settings
menu sets the
OSD position in five locations. Use
/
to select a preferred position.
•
Language
in the
SYSTEM SETUP: Basic
menu sets your familiar language for the
OSD menus. Use
/
to select your language.
•
Reminder Message
in the
SYSTEM SETUP: Basic
>
Menu Settings
menu sets
whether to display reminder messages on screen. Use
/
to select your desired
setting.
•
Splash Screen
in the
SYSTEM SETUP: Basic
menu sets a preferred logo screen
to be displayed during projector start-up. Use
/
to select a screen.