BenQ MX813ST Short-Throw DLP Projector User Manual - Page 61

Timing of replacing the lamp, Lamp indicator, Economic, MODE/ENTER

Get BenQ MX813ST Short-Throw DLP Projector PDF manuals and user guides View all BenQ MX813ST Short-Throw DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Go to http://lamp.benq.com for a replacement lamp. The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. See "Indicators" on page 65 for details. The following lamp warning displays will remind you to change the lamp. The warning messages below are for reference only. Please follow the actual on-screen instructions to prepare and replace the lamp. Status Message Install a new lamp for optimal performance. If the projector is normally run with Economic selected (see "Getting to know the lamp hour" on page 60), you may continue to operate the projector until the next lamp warning appears. Press MODE/ENTER to dismiss the message. It is strongly recommended that you replace the lamp at this stage. The lamp is a consumable item. The lamp brightness diminishes with use. This is a normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished. Press MODE/ENTER to dismiss the message. The lamp MUST be replaced before the projector will operate normally. Press MODE/ENTER to dismiss the message. "XXXX" shown in the above messages are numbers that vary depending on different models. Maintenance 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Maintenance
61
Timing of replacing the lamp
When the
Lamp indicator
lights up red or a message appears suggesting it is time to
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
Go to
for a replacement lamp.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. See
"Indicators" on page 65
for details.
The following lamp warning displays will remind you to change the lamp.
The warning messages below are for reference only. Please follow the actual on-screen
instructions to prepare and replace the lamp.
"XXXX" shown in the above messages are numbers that vary depending on different models.
Status
Message
Install a new lamp for optimal performance. If the
projector is normally run with
Economic
selected (
see "Getting to know the lamp hour" on
page 60
), you may continue to operate the
projector until the next lamp warning appears.
Press
MODE/ENTER
to dismiss the message.
It is strongly recommended that you replace the
lamp at this stage. The lamp is a consumable item.
The lamp brightness diminishes with use. This is a
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.
Press
MODE/ENTER
to dismiss the message.
The lamp MUST be replaced before the projector
will operate normally.
Press
MODE/ENTER
to dismiss the message.