BenQ PU9730 DLP Projector User Manual - Page 26

Turning the orojector on or off

Get BenQ PU9730 DLP Projector PDF manuals and user guides View all BenQ PU9730 DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

English Turning the orojector on or off Once the projector is correctly located and the power cable and other connections are in place, it is important that the projector is connected and powered on correctly in order to avoid possible dangers such as electric shock and fire. Refer to the following guide to power on the projector. 1. Turn the main power switch to ON, Power light is red after power has been applied. 2. Press the POWER button on the projector or ON button on the remote control to start the projector.The Power and Lamp LED flashes green and the cooling fan start operating. 3. The projected image will be displayed on the screen for a few second while it is warming up. 4. Once the power LED is lit a solid green, the projector is ready for use. Note:The projector will not respond to further commands while it is warming up. 5. If any of the LEDs remain flashing or blink there may be a problem with the start up. Please refer to the Troubleshooting section page 69 Troubleshooting. Note If you attempt to re-start the projector shortly after shutdown, the fans may run for a few minutes to cool down. Press Power again to start the projector after the fans stop and the Power indicator light turns orange 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
English
26
Turning the orojector on or off
Once the projector is correctly located and the power cable and other connections are in place, it
is important that the projector is connected and powered on correctly in order to avoid possible
dangers such as electric shock and fire.Refer to the following guide to power on the projector.
1. Turn the main power switch to ON, Power light is red after power has been applied.
2. Press the POWER button on the projector or ON button on the remote control to start the
projector.The Power and Lamp LED flashes green and the cooling fan start operating.
3. The projected image will be displayed on the screen for a few second while it is warming up.
4. Once the power LED is lit a solid green, the projector is ready for use.
Note: The projector will not respond to further commands while it is warming up.
5. If any of the LEDs remain flashing or blink there may be a problem with the start up.Please refer
to the Troubleshooting section page 69 Troubleshooting.
Note
If you attempt to re-start the projector shortly after shutdown, the fans may run for a few minutes to cool down. Press
Power again to start the projector after the fans stop and the Power indicator light turns orange