Bernina Aurora 440QE User Guide - Page 16

Changing the needle, Bobbin case - aurora 440 qe sewing

Get Bernina Aurora 440QE PDF manuals and user guides View all Bernina Aurora 440QE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

16 Setting up the sewing computer Bobbin case* A To remove the bobbin case • raise the needle • turn power switch to «0» (off) • open the bobbin cover • grasp the latch of the bobbin case • remove case * pictures = aurora 450 To insert the bobbin case • hold the bobbin case latch • aurora 430 / 440 QE: the finger on the case should point upwards • aurora 450: bobbin case opening points up • insert so that it clicks into place Bobbin thread cutter • take the thread over cutter A and cut it • close the bobbin cover • the bobbin thread does not have to be brought up as the loose end is just the right length to start sewing ! Refer to the safety instructions! Changing the needle Removing the needle • raise the needle • turn power switch to «0» (off) • lower the presser foot • loosen the needle clamp screw • pull the needle down to remove Inserting the needle • flat side of needle to the back • insert the needle as far as it will go • tighten the needle clamp screw ! Refer to the safety instructions! 032907.52.04_1103_a430_a440_a450_EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
16
Setting up the sewing computer
Removing the needle
• raise the needle
•
turn power switch to «0» (off)
• lower the presser foot
• loosen the needle clamp screw
•
pull the needle down to remove
Changing the needle
!
Refer to the
safety instructions!
To remove the bobbin case
• raise the needle
•
turn power switch to «0» (off)
• open the bobbin cover
•
grasp the latch of the bobbin case
• remove case
* pictures = aurora 450
Bobbin case*
To insert the bobbin case
• hold the bobbin case latch
•
aurora 430 / 440 QE:
the finger on the
case should point upwards
•
aurora 450:
bobbin case opening points
up
•
insert so that it clicks into place
Bobbin thread cutter
• take the thread over cutter
A
and cut it
• close the bobbin cover
•
the bobbin thread does not have to be
brought up as the loose end is just the
right length to start sewing
!
Refer to the
safety instructions!
Inserting the needle
•
flat side of needle to the back
•
insert the needle as far as it will go
• tighten the needle clamp screw
A
032907.52.04_1103_a430_a440_a450_EN