Bosch SGE53B55UC Use and Care Manual - Page 22

Rinse aid system

Get Bosch SGE53B55UC PDF manuals and user guides View all Bosch SGE53B55UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

en-us Rinse aid system ¡ The water hardness is 0 - 8 °E. You can omit special salt. 1. Press . 2. To open the basic settings, press for 3 seconds. a The display shows Hxx. a The display shows . 3. Press repeatedly until the display shows H00. 4. To save the settings, press for 3 seconds. a The water softening system is switched off and the salt refill indicator is deactivated. Rinse aid system 10 Rinse aid system Rinse aid system You can use the rinse aid system and rinse aid to get dishware and glasses rinsed perfectly without spots. 10.1 Rinse aid For optimum drying results, use rinse aid. Only use rinse aid intended for household dishwashers. Adding rinse aid If the rinse aid refill indicator lights up, fill the dispenser with rinse aid. Only use rinse aid intended for household dishwashers. 1. Press the catch on the lid of the dispenser for rinse aid and lift . 2 1 2. Add rinse aid up to the max mark. max 3. If rinse aid spills out, remove it from the tub. Spilled rinse aid can cause excessive frothing during the wash cycle. 4. Close the lid of the dispenser for rinse aid. a The lid clicks into position. 10.2 Setting the amount of rinse aid If there are streaks or water spots on dishware, change the amount of rinse aid. 1. Press . 2. To open the basic settings, press for 3 seconds. a The display shows Hxx. a The display shows . 3. Press repeatedly un- til the display shows the value set at the factory r05. 4. Press repeatedly until the right amount of rinse aid has been set. - A low setting adds less rinse aid during the wash cycle and reduces streaking on dishware. - A higher setting adds more rinse aid during the wash cycle, reduces water spots and improves the drying result. 5. To save the settings, press for 3 seconds. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
en-us
Rinse aid system
22
¡
The water hardness is 0 - 8 °E.
You can omit special salt.
1.
Press
.
2.
To open the basic settings,
press
for 3 seconds.
a
The display shows Hxx.
a
The display shows
.
3.
Press
repeatedly until the
display shows H00.
4.
To save the settings, press
for 3 seconds.
a
The water softening system is
switched off and the salt refill
indicator is deactivated.
10
Rinse aid system
You can use the rinse aid system
and rinse aid to get dishware and
glasses rinsed perfectly without
spots.
10.1
Rinse aid
For optimum drying results, use
rinse aid.
Only use rinse aid intended for
household dishwashers.
Adding rinse aid
If the rinse aid refill indicator lights
up, fill the dispenser with rinse
aid. Only use rinse aid intended
for household dishwashers.
1.
Press the catch on the lid of the
dispenser for rinse aid
and
lift
.
1
2
2.
Add rinse aid up to the max
mark.
max
3.
If rinse aid spills out, remove it
from the tub.
Spilled rinse aid can cause ex-
cessive frothing during the
wash cycle.
4.
Close the lid of the dispenser
for rinse aid.
a
The lid clicks into position.
10.2
Setting the amount
of rinse aid
If there are streaks or water spots
on dishware, change the amount
of rinse aid.
1.
Press
.
2.
To open the basic settings,
press
for 3 seconds.
a
The display shows Hxx.
a
The display shows
.
3.
Press
repeatedly un-
til the display shows the value
set at the factory r05.
4.
Press
repeatedly until the
right amount of rinse aid has
been set.
–
A low setting adds less rinse
aid during the wash cycle
and reduces streaking on
dishware.
–
A higher setting adds more
rinse aid during the wash cy-
cle, reduces water spots and
improves the drying result.
5.
To save the settings, press
for 3 seconds.