Bosch SHE5AM02UC Use & Care Manual - Page 12

OPERATING THE SHE5AM, To start unit - 01

Get Bosch SHE5AM02UC - Full Console Dishwasher PDF manuals and user guides
UPC - 825225862598
View all Bosch SHE5AM02UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

OPERATING THE SHE5AM To start unit: - Door must be closed. Press the ON/OFF button to turn the unit on. - Countdown display and Wash cycle LED will be flashing to indicate pre-select mode. - Press or to select desired wash cycle. - If desired, select "Half Load" or "Delay Start" (1-24 hrs). - Press START to begin cycle. Child Lock - After pressing START you can activate the child lock feature. - Press and hold until "CL" appears in the display. Now any button you press (except ON/OFF) will not function and "CL" will display each time. - To deactivate: press and hold until "CL" disappears from the display. WARNING You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR CAREFULLY during any wash or rinse cycle. Do not fully open the door until water noises have stopped. To cancel cycle: NOTE: Child lock needs to be deactivated - Press the "Start Reset " button and hold for 3 seconds. the display will change to "0:01" - Wait until display shows "0:00" and turn unit off. NOTE: You cannot cancel a cycle with child lock activated. Setting Options (Extra Dry Heat / Rinse Agent Amount) - Door must be closed. Turn unit on. - Wash cycle LED will be flashing to indicate pre-select mode. - To enter setup mode press and hold then press and release START button; then release . Sanitized LED will be flashing to indicate setup mode. NOTE: Rinse Agent LED will be illuminated if unit needs rinse agent. To set Extra Dry Heat: Press until "d:00" or "d:01" appear in the display - Press to change setting Display shows: d:00 extra dry heat OFF Display shows: d:01 extra dry heat ON NOTE: Press to switch between Extra dry Heat and Rinse Agent options To set Rinse Agent amount: Press until "r:0#" appears in the display. - Press to adjust amount of rinse aid dispensed from "r:00 " (no rinse agent) to "r:06" (largest amount dispensed) - End and save with the START button. NOTE: If your glasses have spots you need more Rinse Agent. If your glasses have streaks you need less Rinse Agent. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
12
OPERATING THE SHE5AM
To start unit:
- Door must be closed. Press the ON/OFF button to turn the unit on.
- Countdown display and Wash cycle LED will be flashing to indicate pre-select mode.
- Press
or
to select desired wash cycle.
- If desired, select “Half Load” or “Delay Start” (1-24 hrs).
- Press START to begin cycle.
Child Lock
- After pressing START you can activate the child lock feature.
- Press and hold
until "CL" appears in the display. Now any button you press (except ON/OFF) will not
function and “CL” will display each time.
- To deactivate: press and hold
until “CL” disappears from the display.
WARNING
You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR CAREFULLY
during any wash or rinse cycle. Do not fully open the door until water noises have stopped.
To cancel cycle:
NOTE: Child lock needs to be deactivated
- Press the “Start
Reset “
button and hold for 3 seconds. the display will change to “0:01”
- Wait until display shows “0:00” and turn unit off.
NOTE
: You cannot cancel a cycle with child lock activated.
Setting Options (Extra Dry Heat / Rinse Agent Amount)
- Door must be closed. Turn unit on.
- Wash cycle LED will be flashing to indicate pre-select mode.
- To enter setup mode press and hold
then press and release START button; then release
.
Sanitized LED will be flashing to indicate setup mode.
NOTE: Rinse Agent LED will be illuminated if unit needs rinse agent.
To set Extra Dry Heat:
Press
until “d:00” or “d:01” appear in the display
- Press
to change setting
Display shows: d:00
extra dry heat OFF
Display shows: d:01
extra dry heat ON
NOTE: Press
to switch between Extra dry Heat and Rinse Agent options
To set Rinse Agent amount:
Press
until “r:0#” appears in the display.
- Press
to adjust amount of rinse aid dispensed from “r:00 “ (no rinse agent) to “r:06” (largest amount dispensed)
- End and save with the
START button.
NOTE: If your glasses have spots you need more Rinse Agent. If your glasses have streaks you need less Rinse Agent.