Bosch SHE5AM02UC Use & Care Manual - Page 13

OPERATING THE, To start unit, SHE4AM1, SHE4AM0

Get Bosch SHE5AM02UC - Full Console Dishwasher PDF manuals and user guides
UPC - 825225862598
View all Bosch SHE5AM02UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

OPERATING THE: SHE4AM0 SHE4AM1 To start unit: - Door must be closed. Press the ON/OFF button to turn the unit on. - Program LEDs will be flashing to indicate "pre-select" mode. - Press or to select desired cycle. - If desired press "Delay start" to select 3/6/9 hour delayed start. If desired press the Half Load option (SHE4AM1 models only) - Press start to begin cycle. Program select LED stops flashing and Active LED illuminates. NOTE: Rinse Agent LED will be illuminated if unit needs rinse agent. Child Lock - After pressing START you can activate the Child Lock feature. - Press and hold until "Child Lock" LED illuminates. LED goes off once you release the button. Child lock is activated. Now any button you press (except ON/OFF) will not function and the child lock LED will illuminate each time to indicate this - To deactivate: press and hold until the child lock LED goes out. WARNING You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR CAREFULLY during any wash or rinse cycle. Do not fully open the door until water noises have stopped. To cancel cycle: NOTE: Child lock needs to be deactivated - Press and hold the "Start Reset " button for 3 seconds. The unit will drain any remaining water ( takes about 1 minute), active LED goes out and Clean LED illuminates. - Turn unit off. Setting Options (Extra Dry Heat / Rinse Agent Amount) - Door must be closed. Turn unit on. - Wash cycle LED will be flashing to indicate pre-select mode. - To enter "setup" mode press and hold then press and release "Start Reset" button; then release . - Clean and one other LED will be flashing to indicate setup mode. - Press to select an option (Extra Dry Heat / Rinse Agent Amount) - Press to adjust the setting for the respective option. To set Extra Dry Heat: Clean & Sanitized LED flashing Power Scrub Heat Setting Extra Dry ON Extra Dry OFF SHE4AM0 SHE4AM1 - Press to switch between the Heat and Rinse Agent options. - Press START to save To set Rinse Agent amount: Clean + Rinse Agent LED flashing Power Scrub Power Scrub Regular Wash Auto Wash Quick Wash Regular Wash Rinse & Hold Quick Wash Rinse Aid Setting 0 1 2 3 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
13
OPERATING THE:
To start unit:
- Door must be closed. Press the ON/OFF button to turn the unit on.
- Program LEDs will be flashing to indicate “pre-select” mode.
- Press
or
to select desired cycle.
- If desired press “Delay start” to select 3/6/9 hour delayed start. If desired press the Half Load option (SHE4AM1 models only)
- Press start to begin cycle. Program select LED stops flashing and Active LED illuminates.
NOTE: Rinse Agent LED will be illuminated if unit needs rinse agent.
Child Lock
- After pressing START
you can activate the Child Lock feature.
- Press and hold
until "Child Lock" LED illuminates. LED goes off once you release the button. Child lock is activated.
Now
any button you press (except ON/OFF) will not function and the child lock LED will illuminate each time to indicate this
- To deactivate: press and hold
until the child lock LED goes out.
WARNING
You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR CAREFULLY during
any wash or rinse cycle. Do not fully open the door until water noises have stopped.
To cancel cycle:
NOTE: Child lock needs to be deactivated
- Press and hold the “Start
Reset “
button for 3 seconds.
The unit will drain any remaining water ( takes about 1 minute), active LED goes out and Clean LED illuminates.
- Turn unit off.
Setting Options (Extra Dry Heat / Rinse Agent Amount)
- Door must be closed. Turn unit on.
- Wash cycle LED will be flashing to indicate pre-select mode.
- To enter “setup” mode press and hold
then press and release “Start Reset” button; then release
.
- Clean and one other LED will be flashing to indicate setup mode.
-
Press
to select an option (Extra Dry Heat / Rinse Agent Amount)
- Press
to adjust the setting for the respective option.
To set Extra Dry Heat
: Clean & Sanitized LED flashing
Power Scrub
Heat Setting
Extra Dry ON
Extra Dry OFF
- Press
to switch between the Heat and Rinse Agent options.
- Press START to save
To set Rinse Agent amount
: Clean + Rinse Agent LED flashing
SHE4AM1
SHE4AM0
SHE4AM1
SHE4AM0
Power
Scrub
Regular
Wash
Quick
Wash
Rinse &
Hold
Rinse Aid
Setting
Power
Scrub
Auto
Wash
Regular
Wash
Quick
Wash
0
1
2
3