Bosch SHE68E05UC Instructions for Use - Page 17

Delay start, Cycle Completion Signal, Intensive drying, InfoLight - installation

Get Bosch SHE68E05UC - 24inch Evolution 800 PDF manuals and user guides
UPC - 825225868330
View all Bosch SHE68E05UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

InfoLight * An LED illuminates the floor to indicate the unit is running. Do not open the dishwasher door until the LED is no longer visible on the floor. If the appliance is installed at eye-level, the LED is not visible. To change the setting: • Turn unit on by pressing the [ON/OFF] button. • Hold down the "A" button (see page 4) and press [START] until the display indicates "H:00". • Release both buttons. • The LED for "A" flashes and display indicates "H:04". • Press the "A" button until the display shows "1:01". • Press the "C" button to switch between "1:01"= ON and "1:00" = OFF and press [START] to save setting. Delay start You can delay the start of the cycle in one hour increments up to 24 hours. • Open the door (for hidden controls only). • Turn unit on using the [ON/OFF] button. • Press [+] until the display jumps to "h:01". • Press [+] or [-] until the displayed time corresponds with your requirements. "h:01" = 1 hour delay "h:24" = 24 hour delay • Press [START]. Delay start is activated. To cancel delay start: • Press the [+] or [-] button until "h:00" is indicated on the digital display. You can change your selection at any time until the program starts. • Close the door (for hidden controls only). Cycle Completion Signal The cycle completion is indicated by a tone. This function can be changed as follows: • Open the door (for hidden controls only). • Turn unit on using the [ON/OFF] button. • Hold down the "A" button (see page 4) and press [START] until the display shows "H:00". • Release both buttons. • Press the "A" button until the display shows "b:02". • Press the "C" button to increase or decrease the tone. "b:00" = off and "b:03" = loudest • Press [START] to save the setting. • Close the door (for hidden controls only). Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Use caution if utensils are delicate!) • Open the door (for hidden controls only). • Turn unit on using the [ON/OFF] button. • Hold down the "A" button (see page 4) and press [START] until the display shows "H:00". • Release both buttons. • Press the "A" button until the display indicates "d:00". To change the setting, • Press the "C" button to turn intensive drying on or off. "d:01" = ON or "d:00" = OFF • Press [START] to save the setting. • Close the door (for hidden controls only).    * model dependent   16  

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Delay start
You can delay the start of the cycle in one hour increments up to 24 hours.
•
Open the door (for hidden controls only).
•
Turn unit on using the
[
ON/OFF
]
button.
•
Press
[+]
until the display jumps to
“h:01”
.
•
Press
[+]
or
[–]
until the displayed time corresponds with your requirements.
“h:01”
= 1 hour delay
“h:24”
= 24 hour delay
•
Press
[
START
]
. Delay start is activated.
To cancel delay start:
•
Press the
[+]
or
[–]
button until
“h:00”
is indicated on the digital display.
You can change your selection at any time until the program starts.
•
Close the door (for hidden controls only).
Cycle Completion Signal
The cycle completion is indicated by a tone. This function can be changed as follows:
•
Open the door (for hidden controls only).
•
Turn unit on using the
[
ON/OFF
]
button.
•
Hold down the
“A”
button (see page 4) and press
[
START
]
until the display shows
“H:00”
.
•
Release both buttons.
•
Press the
“A”
button until the display shows
“b:02”
.
•
Press the
“C”
button to increase or decrease the tone.
“b:00”
= off and
“b:03”
= loudest
•
Press
[
START
±
to save the setting.
•
Close the door (for hidden controls only).
Intensive drying
The final rinse uses a higher temperature which improves the drying result.
The running time may increase slightly. (Use caution if utensils are delicate!)
•
Open the door (for hidden controls only).
•
Turn unit on using the
[
ON/OFF
]
button.
•
Hold down the
“A”
button (see page 4) and press
[
START
]
until the display shows
“H:00”
.
•
Release both buttons.
•
Press the
“A”
button until the display indicates
“d:00”
.
To change the setting,
•
Press the
“C”
button to turn intensive drying on or off.
“d:01”
= ON or
“d:00”
= OFF
•
Press
[
START
]
to save the setting.
•
Close the door (for hidden controls only).
* model dependent
16
InfoLight
*
An LED illuminates the floor to indicate the unit is running. Do not open the dishwasher door until the LED is no longer
visible on the floor. If the appliance is installed at eye-level, the LED is not visible.
To change the setting:
•
Turn unit on by pressing the
[
ON/OFF
]
button.
•
Hold down the
“A”
button (see page 4) and press
[
START
]
until the display indicates
“H:00”
.
•
Release both buttons.
•
The LED for
“A”
flashes and display indicates
“H:04”
.
•
Press the
“A”
button until the display shows
“1:01”
.
•
Press the
“C”
button to switch between
“1:01”
= ON and
“1:00”
= OFF and press
[
START
]
to save setting.