Bosch SHX68T55UC Instructions for Use - Page 18

Start the dishwasher, Cancel a cycle, Interrupt a cycle, Delay Start, Cycle Completion Signal hidden - 02

Get Bosch SHX68T55UC PDF manuals and user guides View all Bosch SHX68T55UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

NOTE: For models with hidden controls, the door must be opened before changing settings and closed after changing settings. Buttons are sensitive and should be touched gently. Avoid any grease or food particals resting on the buttons as they could activate the dishwasher. Wiping and cleaning can also activate the dishwasher. For best results, use bare, clean hands when touching the buttons. NOTICE: Use caution when opening door during a running cycle. Hot water may splash out. Open door slowly. Start the dishwasher 1 Press the [On/Off] button. The LED of the last selected cycle flashes. 2 Select a cycle and desired options and press [Start]. Cancel a cycle 1 Press and hold the [Start] button for approximately 3 seconds until the display reads "0:01". 2 Wait about 1 minute while the dishwasher drains. 3 Open the door and press the [On/Off] button. Interrupt a cycle 1 Press the [On/Off] button to turn the unit off. 2 To resume the cycle, press the [On/Off] button again. Delay Start You can delay the start of the cycle in one hour increments up to 24 hours. To set delay start: 1 Press the [On/Off] button. Select a cycle. 2 Press the [Delay] button until the displayed time corresponds with your requirements and press [Start] to activate delay start. h:01 = 1 hour delay h:24 = 24 hour delay To cancel delay start: 1 Press the [Delay] button until "h:00" is indicated on the digital display. 2 Press [Start] to save setting. Cycle Completion Signal (hidden controls only) 1 Open the door and press the [On/Off] button. 2 Hold down the "A" button (see page 16) and press [Start] until the display indicates "d:00". Release both buttons. 3 Press the "A" button until the display shows "b:02". 4 Press the "C" button to increase or decrease the tone "b:00" = OFF and "b:03" = LOUDEST and press [Start] to save setting and close the door. Intensive Drying The final rinse uses a higher temperature which improves the drying results. The running time may increase slightly. To turn intensive drying on: 1 Press the [On/Off] button. 2 Hold down the "A" button and press [Start] until the display indicates "d:00". Release both buttons 3 Press the "A" button until the display shows "d:00". 4 Press the "C" button to turn intensive drying on or off. "d:01" = ON 17 and "d:00" = OFF and press [Start] to save setting.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
17
NOTE: For models with hidden controls, the door must be opened before changing
settings and closed after changing settings.
Buttons are sensitive and should be touched gently. Avoid any grease or food parti-
cals resting on the buttons as they could activate the dishwasher. Wiping and clean-
ing can also activate the dishwasher. For best results, use bare, clean hands when
touching the buttons.
NOTICE: Use caution when opening door during a running cycle. Hot water may
splash out. Open door slowly.
Start the dishwasher
1
Press the
[On/Off]
button. The LED of the last selected cycle flashes.
2
Select a cycle and desired options and press
[Start]
.
Cancel a cycle
1
Press and hold the
[Start]
button for approximately 3 seconds until the
display reads
“0:01”.
2
Wait about 1 minute while the dishwasher drains.
3
Open the door and press the
[On/Off]
button.
Interrupt a cycle
1
Press the
[On/Off]
button to turn the unit off.
2
To resume the cycle, press the
[On/Off]
button again.
Delay Start
You can delay the start of the cycle in one hour increments up to 24 hours.
To set delay start:
1
Press the
[On/Off]
button. Select a cycle.
2
Press the
[Delay]
button until the displayed time corresponds with
your requirements and press
[Start]
to activate delay start.
h:01
= 1 hour delay
h:24
= 24 hour delay
To cancel delay start:
1
Press the
[Delay]
button until “
h:00
” is indicated on the digital display.
2
Press
[Start]
to save setting.
Cycle Completion Signal (hidden controls only)
1
Open the door and press the
[On/Off]
button.
2
Hold down the “
A
” button (see page 16) and press
[Start]
until the
display indicates “
d:00
”. Release both buttons.
3
Press the “
A
” button until the display shows “
b:02
”.
4
Press the “
C
” button to increase or decrease the tone “
b:00
” = OFF and
“
b:03
” = LOUDEST
and press
[Start]
to save setting and close the door.
Intensive Drying
The final rinse uses a higher temperature which improves the drying
results. The running time may increase slightly.
To turn intensive drying on:
1
Press the
[On/Off]
button.
2
Hold down the “
A
” button and press
[Start]
until the display indicates
“
d:00
”. Release both buttons
3
Press the “
A
” button until the display shows “
d:00
”.
4
Press the “
C
” button to turn intensive drying on or off. “
d:01
” = ON
and “
d:00
” = OFF
and press
[Start]
to save setting.