Bosch SPE53B52UC Use and Care Manual - Page 44

Issue, Cause and troubleshooting, Reset

Get Bosch SPE53B52UC PDF manuals and user guides View all Bosch SPE53B52UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

en-us Troubleshooting Issue Cause and troubleshooting Water is left in the Filter system or area under the filters is blocked. appliance at the end 1. Clean the Filters → Page 33. of the program. 2. Clean the Wastewater pump → Page 45. Program has not yet ended. ▶ Wait until the program ends or terminate the program with Reset. ▶ → "Terminating the wash cycle", Page 27 Appliance cannot be Software update is taking place. switched on or oper- ▶ Wait until the software update has finished. ated. Appliance functions have failed. 1. Pull out the power cord plug or switch off the breaker. 2. Wait at least 2 minutes. 3. Connect the appliance to the power supply. 4. Switch the appliance on. Appliance does not The breaker has tripped. start. ▶ Check the relevant breaker. Power cord is not inserted. 1. Check whether the power outlet is working. 2. Check whether the power cord plug is properly inserted in the power outlet and on the rear of the appliance. Appliance door is not closed properly. ▶ Close the appliance door. Wash cycle starts You did not wait until the cycle ended. up automatically. ▶ → "Terminating the wash cycle", Page 27 Appliance stops dur- Appliance door is not closed properly. ing the cycle or cuts ▶ Close the appliance door. out. Power and/or water supply has been interrupted. 1. Check the power supply. 2. Check the water supply. Upper rack is pressing against inner door and preventing appliance door from being closed securely. ▶ Check whether the rear panel of the appliance is being pressed in by a power outlet or a hose holder that has not been removed. ▶ Arrange the dishware so that no parts project beyond the rack and prevent the appliance door from closing properly. 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
en-us
Troubleshooting
44
Issue
Cause and troubleshooting
Water is left in the
appliance at the end
of the program.
Filter system or area under the filters is blocked.
1.
Clean the Filters
→
Page 33
.
2.
Clean the Wastewater pump
→
Page 45
.
Program has not yet ended.
▶
Wait until the program ends or terminate the
program with
Reset
.
▶
→
"Terminating the wash cycle", Page 27
Appliance cannot be
switched on or oper-
ated.
Software update is taking place.
▶
Wait until the software update has finished.
Appliance functions have failed.
1.
Pull out the power cord plug or switch off the
breaker.
2.
Wait at least 2 minutes.
3.
Connect the appliance to the power supply.
4.
Switch the appliance on.
Appliance does not
start.
The breaker has tripped.
▶
Check the relevant breaker.
Power cord is not inserted.
1.
Check whether the power outlet is working.
2.
Check whether the power cord plug is properly
inserted in the power outlet and on the rear of
the appliance.
Appliance door is not closed properly.
▶
Close the appliance door.
Wash cycle starts
up automatically.
You did not wait until the cycle ended.
▶
→
"Terminating the wash cycle", Page 27
Appliance stops dur-
ing the cycle or cuts
out.
Appliance door is not closed properly.
▶
Close the appliance door.
Power and/or water supply has been interrupted.
1.
Check the power supply.
2.
Check the water supply.
Upper rack is pressing against inner door and
preventing appliance door from being closed se-
curely.
▶
Check whether the rear panel of the appliance
is being pressed in by a power outlet or a hose
holder that has not been removed.
▶
Arrange the dishware so that no parts project
beyond the rack and prevent the appliance
door from closing properly.