Home » Bosch Manuals » Laundry Washers » Bosch WAW285H2UC » Manual Viewer

Bosch WAW285H2UC Instructions for Use - Page 25

Starting the program, Selecting a different program, Pausing/Adding a garment to the cycle, Cancel

Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Liquid detergent insert To measure liquid detergent: 1. Pull out the detergent dispenser tray. 2. Push the liquid detergent insert forward and down as shown. 3. Pour liquid detergent into the chamber and do not exceed the maximum mark. 4. Reinsert the tray into its compartment. NOTICE: Do not use the liquid detergent insert with geltype detergents and powdered detergents or for cycles with pre-wash or selected "Finish in" time. Starting the program Press the Start/Pause button. Indicator lamp lights up and the program starts. NOTICE: If you want to protect the cycle against inadvertent adjustment, select the Child lock. ~ Child lock; Page 37 The display panel shows the "Finish in" time before the program starts or the program length and the program progress symbols when the washing program has started. ~ Display area; Page 21 Foam detection If you use too much detergent, too much foam may be formed during the wash cycle. The symbol Å lights up. Foam may be also leaking out from the detergent drawer. In order to remove the foam, the appliance automatically activates additional rinse cycles. This extends program duration. NOTICE: To prevent excess foaming use less detergent in subsequent wash loads. Selecting a different program If you have inadvertently started the wrong program, you can change this as follows: 1. Press Start/Pause. 2. Select another program. 3. Press Start/Pause. The new cycle starts from the beginning. Pausing/Adding a garment to the cycle Pausing the wash cycle can be useful for several purposes. e.g. for soaking ~ Soaking; Page 35 Press Start/Pause. The indicator lamp A is blinking. Wash load will soak in water until continued by pressing Start/Pause. For adding a garment after the cycle begins. 1. Press Start/Pause. Door will unlock when safe to do so. 2. Open door carefully and add or remove laundry item. NOTICE: You can do this as long as the Start/Pause indicator flashes and it is safe to do so. 3. Close door. 4. Press Start/Pause. The cycle continues. NOTICE: If the cycle is paused but the door will not unlock it could be for safety reasons (high water level, water temperature or drum speed). Cancel program For cycles with a high temperature: 1. Press Start/Pause. 2. Cool the laundry off: Select Rinse. 3. Press Start/Pause. For cycles with a low temperature: 1. Press Start/Pause. 2. Select Spin/Drain and Spin Speed option to No Spin. 3. Press Start/Pause. Program end - ‹- appears in the display field and the Start/Pause button indicator lamp is off. NOTICE: If this symbol Åappears in the display, the washer has detected too much foam and it automatically adds an additional rinse cycles to remove the foam. Use less detergent the next time you run the washer with the similar load. 25

Section	Page
en-us Use and Care Manual, Installation Instructions	1
Washer	1
Table of contentsen-us Use and Care Manual, Installation Instructions	3
Your washing machine is intended for 6	3
Safety Definitions 6	3
IMPORTANT SAFETY INSTRUCTIONS 7	3
Introduction to your new washer 9	3
Dimensions and clearances required 10	3
Installation instructions 12	3
Getting to know your appliance 20	3
Operating Instructions 23	3
Home Connect 27	3
Laundry 31	3
Laundry detergents and additives 33	3
Program selection table 34	3
Optional program settings 36	3
Appliance settings 37	3
Cleaning and maintenance 38	3
Troubleshooting 41	3
STATEMENT OF LIMITED PRODUCT WARRANTY 45	3
Additional information on products, accessories, replacement parts and services can be found at www.bosch-home.com/us and in the online shop www.bosch-home.com/us/store	4
Important information	4
Purchase information	4
Please take a moment to record the following basic information about your new Bosch washer.	4
This information will be helpful in the event you need to contact Customer Service or would like to order accessories or replacement parts.	4
The E-Nr. (model number) and the FD (serial) number are found on the rating plate label.	4
see illustration	4
The model number includes the slash and a two digit number (e.g. \	4
Date of Purchase:___/___/_____	4
Where Purchased:___________________________	4
E-Nr. :_________/____ (ex: WAW285H2UC/01)	4
FD :_______-_______ (ex: 9709\|90007)	4
The manufacturer reserves the right to make changes in the product or manual without notification.	4
Customer service	5
Your washer does not require any special care other than the maintenance and care mentioned in this manual. If you have a problem with your washer, please consult.	5
~ Troubleshooting; Page 41	5
This may save you money. If a technician comes out to advise you of information that is in the Troubleshooting table you may be charged.	5
If problems persist and service becomes necessary, contact your dealer, installer or an authorized service center. Do not attempt to repair the appliance yourself. Any work performed by unauthorized personnel may void the warranty.	5
If you are having a problem with your washing machine and are not pleased with the service you have received, please follow these steps:	5
1. Contact your installer or the Authorized Service Provider in your area and explain to them why you are not satisfied. This will usually correct the problem.	5
2. If after working with your installer or service technician the problem still has not been resolved to your satisfaction, please let us know either by writing to us at: BSH Home Appliances Corporation 1901 Main Street, Suite 600 Irvine, CA 92614 or...	5
When writing or calling please have the following information available:	5
If writing, please also include a daytime telephone number and a copy of the sales invoice.	5
When calling Customer Service, please be ready to provide the model number E-Nr. and FD serial number. This information will help provide the best support for your washer.	5
Additional information is available at our website.	5
Your washing machine is intended for	6
NOTICE:	6
Read the use and installation instructions and all other information included with the washer and act accordingly.	6
Keep all documents for future use.	6
Safety Definitions	6
Important safety information is contained in this manual and on the warning labels located on your washer.	6
Standard symbols and headings are used to identify areas where you should take precautions to avoid injury or damage. Please take a moment to become familiar with each of these symbols and what they mean before proceeding.	6
9 WARNING	6
9 CAUTION	6
NOTICE:	6
Tip:	6
IMPORTANT SAFETY INSTRUCTIONS	7
READ AND SAVE THESE INSTRUCTIONS	7
WARNING	7
WARNING	7
▯ Bosch washers are provided with an Use and Care and Installation Instruction manual. Read and understand all instructions before using the washing machine.	7
▯ Do not wash articles that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode.	7
▯ Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.	7
▯ Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for this length of time, turn on all hot water faucets an...	7
▯ Before the appliance is removed from service or discarded, remove the door to prevent children from playing or hiding inside. Also remove the power cord/ plug.	7
▯ Do not allow anyone to climb, lean or hang on any part of the washer including any protruding components such as the appliance door or a pullout shelf.	7
▯ Use caution when draining hot water from the washer drum such as during pump maintenance or when using the emergency door open procedure.	7
▯ Do not reach into the appliance if the wash drum is moving.	7
▯ Do not tamper with the controls.	7
▯ Do not repair or replace any part of the appliance or attempt any service unless specifically recommended in the user manual or in Bosch published user repair instructions that you understand and have the skills to carry out.	7
▯ Always unplug the washing machine from the power supply before attempting any service. Disconnect the power cord by grasping the plug, not the cord.	7
▯ Do not machine wash fiberglass materials (such as curtains and window coverings that use fiberglass materials). Small particles may remain in the washing machine and stick to fabrics in subsequent wash loads causing skin irritation.	7
▯ Do not install or store the washer where it will be exposed to the weather. Hoses and internal parts may be damaged if exposed to freezing temperatures.	7
▯ Do not use the washing machine if it has a worn power cord or loose plug.	7
▯ The washing machine must only be used for its intended purpose.	7
▯ Always follow the fabric care instructions recommended by the clothing manufacturer.	7
▯ Make sure all water connections to the washing machine have shut-off valves that are readily accessible during normal operation of the washer. Turn off both valves during periods in which the washer is not in use and before leaving for extended p...	7
▯ Do not operate the washing machine if parts are missing or broken.	7
▯ Do not operate the washing machine until you are sure that:	7
▯ Certain internal parts are intentionally not grounded and may present a risk of electric shock during servicing. Service Personnel – DO NOT CONTACT the following parts while the appliance is energized: inlet valves, drain pump, heat sink of the...	7
▯ See the installation instructions in this manual for grounding requirements.	7
IMPORTANT SAFETY INSTRUCTIONS	8
READ AND SAVE THESE INSTRUCTIONS	8
WARNING	8
▯ Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.	8
▯ Make sure to utilize all child lock/safety features of your appliance, and be sure to turn the appliance Off when not in use.	8
▯ Appliances are not intended for use by children, however when children become old enough to operate the appliance, it is the responsibility of the parents or legal guardians to ensure they are instructed in safe practices by qualified persons.	8
▯ Keep all laundry aids (including detergents, bleach, fabric softener, etc.) out of the reach of children.	8
WARNING	8
Introduction to your new washer	9
9 WARNING	9
risk of fire, electric shock or injury	9
Standard features and helpful information	9
Thank you for choosing Bosch for your laundry appliance needs.	9
Please read and follow the use and care, important safety instructions and troubleshooting information contained in this manual. Please retain this manual for future reference.	9
Standard features	9
Quality tested	9
Every Bosch washer is thoroughly tested before leaving the factory. As a result, a small amount of residual water may remain in the washer drum. We recommend running the Drum Clean cycle to remove this water prior to washing your first load of laundry.	9
~ Before loading your first load of laundry; Page 23	9
Website	9
Visit our website at www.bosch-home.com/us for more information and to view a selection of our products.	9
About this manual	9
These operating and installation instructions may apply to more than one model of washer. Illustrations used may show details that differ from your particular model.	9
Read your user manual. It contains valuable information about safety, installation and operation of your new appliance.	9
This can save you time, make it easier to correctly install and use your washer, and improve your overall satisfaction with your new appliance.	9
Special features	9
Environmentally friendly use of your washer	9
Your new Bosch washing machine is designed to use water, energy and detergent in a highly efficient way to help reduce operating costs, conserve resources and protect the environment.	9
Dimensions and clearances required	10
Appliance dimensions	10
Length of power cord and water supply hoses	10
Installation types	10
Stacked washer and dryer	10
A Bosch dryer of the same dimensions can be placed on top of the washer to save space.	10
Use the special washer-dryer stacking kits (noted in Bosch Dryer User Manuals) which can be purchased from customer service or your local dealer.	10
Stand alone (shown) or Side-by-Side	11
Under counter (Preferred)	11
Front of the appliance fully open.	11
No doors or coverings.	11
Under counter (Less Desirable)	11
If front of the appliance is covered ventilation openings must be installed.	11
Installation instructions	12
9 WARNING	12
Risk of fire, electrical shock or injury to persons	12
9 CAUTION	12
Washing machine is heavy	12
Introduction	12
Read these installation instructions completely and carefully before starting to install your new washing machine. The information contained can save you time and effort and will help to ensure optimum performance of your new washer. Be sure to obser...	12
NOTICES	12
These installation instructions are intended for use by qualified installers. In addition to these instructions, the installation must comply with:	12
- for the United States - National Electrical Code, ANSI/ NFPA70 - and latest editions of the State and municipal and/or local regulations.	12
- for Canada - Canadian Electrical Code C22.1 - and the latest editions of the Provincial, Municipal and/or local regulations.	12
Tools needed	12
The following tools may be helpful during installation of your washer.	12
Waste disposal	12
Disposal of Packaging Materials	12
After unpacking your new appliance dispose of the protective packaging materials in an environmentally friendly way. Ask your dealer or inquire with your local authority regarding currently acceptable means of disposal.	12
9 WARNING	12
Warnings for children	12
Disposal of Your Old Appliance	12
Your old appliance can be recycled if it is no longer to be used. Prior to disposing of your old appliance observe the following precautions to reduce safety risks.	12
9 WARNING	12
To avoid risk of injury or death, do the following	12
Parts provided with your washer	13
Back side of the washing machine	13
Washer drum contents	13
Two AquaShield ® water supply hoses are shipped in the washer drum. Be sure to remove each of these and use these new hoses for the installation.	13
NOTICE:	13
Set up on a pedestal with drawer	13
Pedestal item number: WMZ 20490	13
Mount washer on the pedestal according to the instructions in the installation kit.	13
Installation checklist	14
Review the following list and check off each step as it is completed during installation.	14
Importance of installing on a solid, level floor	14
Your new Bosch washing machine utilizes high spin speeds to achieve superior water removal from your laundry resulting in reduced drying time. It is important to install your washing machine on a floor that will provide firm support. This prevents th...	14
The installation surface must be solid and level in both directions. Avoid installing your washer on soft surfaces such as floors with carpet or foam backed covering material.	14
If installing the washer on a wooden floor, observe the following:	14
Remove the transport bolts	14
9 CAUTION	14
Damage to the appliance or injury possible	14
1. Remove drain hose from all brackets.	14
2. Loosen and remove all 4 transport bolts. Remove the sleeves. Take the power cable out of the brackets.	14
3. Place covers over the transport bolt holes. Four plastic covers are provided in the small parts bag included with your washer. Separate these covers and install one in each hole where the transport bolts were removed. Lock covers firmly by pressin...	15
NOTICE:	15
Water connections	15
Water supply hose connections	15
NOTICES	15
Connect your washer to the wall faucets using the included AquaShield® water supply hose.	15
Observe each of the following:	15
Water connection hoses	15
Attach this end to water tap. Hand tighten only.	15
Attach this end of the hose to the back of the washing machine as shown in the following pictures. Be sure to use clamps and route hoses as instructed. Hand tighten only.	15
Position hoses as shown when routing hoses to right side of washer (facing from front).	16
Position hoses as shown when routing hoses to left side of washer (facing from front).	16
About the AquaShield® Hose	16
The AquaShield® hose prevents potential flooding in the event the hose develops an internal leak. If the hose leaks, the indicator turns red and water flow is blocked. Once the internal valve in the hose activates (indicator is red) the hose must be...	16
AquaStop® Plus	16
The AquaStop® Plus feature detects water leaks on the internal base, shuts down operation and automatically pumps out water so it cannot make contact with the floor. This feature along with the internal mechanical valve of the double-walled AquaShie...	16
Water drain hose connection	16
NOTICES	16
Height of drain point	16
Height difference between the floor and drainage point: max. 39 in. (100 cm).	16
Types of drainage hookups	16
Standpipe	16
Attach the drain hose to the elbow included with your washer.	16
Position the elbow on the drain hose 4\	16
Sink siphon	17
Secure the drain hose to the sink siphon using a Ø 0.9 - 1.6 in. (20-44 mm) hose clip (available from a hardware store).	17
Wash Basin	17
9 WARNING	17
Scalding	17
NOTICE:	17
Make sure that:	17
Attach the drain hose securely to the wash basin.	17
NOTICE:	17
Leveling the washer	17
Importance of leveling the washer	17
Your new washer uses high spin speeds to remove water at the end of the wash cycle. It is important that your washer is level and that all four washer feet press with equal pressure against the floor. This will help assure the quietest, most vibratio...	17
Follow these steps:	17
1. Install the washer on a level and solid surface, preferably in a corner of a room.	17
2. If the floor is uneven (or unlevel) adjust the washer feet as required to level the washer. Do not place anything under the washer feet to help level the washer.	17
3. Extend the washer feet no more than is necessary. The more the feet are extended, the more vibration the washer will experience. Start with the washer feet turned all the way in and adjust each foot as necessary.	17
4. Use a bubble level to check the top of the washer to make sure it is level side to side and front to rear.	17
5. Press down on each corner of the washer top to make sure the washer doesn’t “wobble“. There should be no \	17
6. When the washer is level and does not wobble, lock the washer feet in place by tightening the locknuts against the washer bottom. Be sure to do this without changing the height of the foot (hold the foot while tightening the locknut).	17
Procedure for adjusting the washer feet:	17
1. After determining which washer feet need to be extended, have someone lift up on the washer slightly to take pressure off the foot to be adjusted.	17
2. Turn the grey plastic foot to extend it downward as far as necessary to raise the corner of the washer the correct amount to level the washer.	17
3. When the height of the foot is correct, use a 17 mm open end wrench to tighten the locknut against the washer bottom. The locknut should be tight against the bottom of the washer to lock the foot in place.	17
Electrical connection	18
9 WARNING	18
Electrical shock hazard	18
9 WARNING	18
Electrical Shock hazard	18
9 WARNING	18
Electrical Shock hazard	18
To reduce the risk of electrical shock:	18
Grounding Instructions	18
9 WARNING	18
Electrical shock hazard	18
Transporting the washer	19
Before transporting the washer	19
1. Disconnect the washer power cord from the wall outlet.	19
2. Turn off the water supply to the washer.	19
3. Disconnect water supply lines from the tap.	19
4. Disconnect the drain hose from the drain location.	19
5. Install the transport bolt assemblies as shown in the following images.	19
Remove the transport bolt hole covers	19
1. Remove all four transport bolt hole covers.	19
2. Pull the tip of the arrow on the cover out slightly to disengage the locking tab.	19
3. Rotate the cover counterclockwise to remove. Repeat for all 4 transport bolt hole covers.	19
Insert the transport bolt assemblies	19
1. Each assembly consists of a plastic bushing and a bolt that extends through the bushings. Unscrew the bolt until the threaded end is flush with the end of the plastic bushing.	19
2. Insert the transport bolt and bushing assembly as shown. The metal housing slides around the bolt through the slot in the plastic bushing as the bushing is slid into place. The open part of the bushing slot should be facing the direction shown to ...	19
3. When the bolt is in place screw it in until the bolt threads engage the drum. Double check and ensure bolts are screwed into threaded holes and not into cracks or crevices. Repeat the process for all 4 transport bolt assemblies before tightening a...	19
Getting to know your appliance	20
Control panel	20
Display area	21
Operating Instructions	23
9 WARNING	23
Before using the washer for the first time	23
Check to make sure your washer has been installed properly by following the installation instructions in this manual.	23
~ Installation instructions; Page 12	23
Check the machine. Never connect the utilities (power or water) to or start a damaged machine! Contact customer service!	23
Check to be sure your household electrical system voltage and the voltage specifications on the washing machine rating plate correspond.	23
Check to be sure the washer hot and cold water supply taps are turned on.	23
Turning the washing machine on and off	23
Center of the program selector is pressed to turn the appliance on or off.	23
Before loading your first load of laundry	23
Your new washing machine was tested before leaving the factory. This process involves running various wash cycles. As a result, a small amount of water may remain in the tub and drainage system. Run a Drum Clean cycle with no laundry to clean the sys...	23
First add 1 to 2 tablespoons of detergent to the main- wash chamber II. Then run the Drum Clean cycle.	23
Wait for the cycle to finish.	23
Using the program selector to choose a wash program	23
NOTICE:	23
~ Child lock; Page 37	23
Use the program selector to select the desired wash program. The dial turns in both directions and when a cycle is selected its time duration appears in the display. The related preset options (temperature, spin speed, etc.) lights are activated.	23
Selecting optional program settings	23
By selecting the optional program settings, you can adjust the washing process to better suit the items you are washing.	23
The optional program settings can be selected and/or deselected depending if they are allowed (not all settings are allowed for all programs) and the cycle’s progress.	23
The indicator lamps of the buttons light up if the setting is active.	23
~ Program selection table; Page 34	23
~ Optional program settings; Page 36	23
Loading the laundry	23
9 WARNING	23
Loosen the laundry being loaded and mix small and large items	23
Unfold the sorted items and place them loosely in the drum. Mix small and large items to help them better distribute in the drum during the spin cycle.	23
Tip:	23
Recommended Load Size	23
Recommended maximum load size can be found:	23
~ Standard features and helpful information; Page 9	23
Tips	24
Filling the detergent and additives compartments	24
NOTICE:	24
Measuring	24
Measure out the detergent and laundry care products according to:	24
Filling	24
9 WARNING	24
Irritation of eyes/skin!	24
Pour the detergent and laundry care product into the appropriate chambers:	24
Tips	24
1. Open the detergent dispenser tray.	24
2. Add detergent or additive.	24
3. Close the detergent dispenser tray completely before starting the wash cycle.	24
Tip:	24
Liquid detergent insert	25
To measure liquid detergent:	25
1. Pull out the detergent dispenser tray.	25
2. Push the liquid detergent insert forward and down as shown.	25
3. Pour liquid detergent into the chamber and do not exceed the maximum mark.	25
4. Reinsert the tray into its compartment.	25
NOTICE:	25
Starting the program	25
Press the Start/Pause button. Indicator lamp lights up and the program starts.	25
NOTICE:	25
~ Child lock; Page 37	25
The display panel shows the \	25
~ Display area; Page 21	25
Foam detection	25
If you use too much detergent, too much foam may be formed during the wash cycle. The symbol Å lights up. Foam may be also leaking out from the detergent drawer. In order to remove the foam, the appliance automatically activates additional rinse cyc...	25
NOTICE:	25
Selecting a different program	25
If you have inadvertently started the wrong program, you can change this as follows:	25
1. Press Start/Pause.	25
2. Select another program.	25
3. Press Start/Pause. The new cycle starts from the beginning.	25
Pausing/Adding a garment to the cycle	25
Pausing the wash cycle can be useful for several purposes.	25
e.g. for soaking ~ Soaking; Page 35	25
Press Start/Pause. The indicator lamp A is blinking. Wash load will soak in water until continued by pressing Start/Pause.	25
For adding a garment after the cycle begins.	25
1. Press Start/Pause. Door will unlock when safe to do so.	25
2. Open door carefully and add or remove laundry item.	25
NOTICE:	25
3. Close door.	25
4. Press Start/Pause.	25
NOTICE:	25
Cancel program	25
For cycles with a high temperature:	25
1. Press Start/Pause.	25
2. Cool the laundry off: Select Rinse.	25
3. Press Start/Pause.	25
For cycles with a low temperature:	25
1. Press Start/Pause.	25
2. Select Spin/Drain and Spin Speed option to No Spin.	25
3. Press Start/Pause.	25
Program end	25
- ‹- appears in the display field and the Start/Pause button indicator lamp is off.	25
NOTICE:	25
Removing laundry/switching the appliance off	26
1. Open the front door of the washer and remove the laundry.	26
2. Press the center of Program Selector to switch off the appliance.	26
3. Turn off the water taps.	26
NOTICES	26
Home Connect	27
This appliance is Wi-Fi enabled and can be controlled remotely via a smartphone or tablet PC.	27
With the Home Connect app, you can use your smartphone or tablet PC to do the following on this appliance:	27
Before you can use the Home Connect functions, you will need to install the Home Connect app on your smartphone or tablet PC, register, connect your appliance once automatically or manually to your home network, and then connect your mobile device to...	27
You can find information about the app on our Home Connect website www.home-connect.com.	27
The availability of the Home Connect function depends on the availability of Home Connect services in your country. Home Connect services are not available in every country.You can find more information here www.home-connect.com.	27
Notes	27
Connecting to your home network automatically	27
If your router has a WPS function, you can connect the appliance to your home network automatically.	27
If your router does not have a WPS function, you will need to connect the appliance to your home network manually.	27
1. Switch the appliance on.	27
2. Press and hold Remote Start for at least 3 seconds.	27
3. Press Start/Pause to connect to the network. \| will flash on the display.	27
4. Activate the WPS function on your home network router within the next 2 minutes.	27
5. Press Remote Start briefly to exit the Home Connect settings.	27
Note:	27
Connecting to your home network manually	28
If your appliance has already been automatically connected to your home network, you can skip the manual connection step.	28
If your router does not have a WPS function, you will need to connect the appliance to your home network manually.	28
1. Switch the appliance on.	28
2. Press and hold Remote Start for at least 3 seconds.	28
3. Turn the program selector to position 2.	28
4. Press Start/Pause to connect to the network. \| will flash on the display.	28
5. Call up the Wi-Fi setting on the mobile device.	28
6. Connect your smartphone or tablet PC to the Home Connect WiFi network and enter the password (key) “HomeConnect”.	28
Note:	28
7. Once you have connected successfully, open the Home Connectؘ app on the mobile device.	28
8. In the Home Connect app, enter the name (SSID) and password (key) for your home network and then select Transfer to appliance.	28
9. Press Remote Start briefly to exit the Home Connect settings.	28
Notes	28
Connecting to the Home Connect app	28
If your appliance is connected to your home network, you can connect it to the Home Connect app.	28
1. Switch the appliance on.	28
2. Press and hold Remote Start for at least 3 seconds.	28
3. Turn the program selector to position 3.	28
4. Press Start/Pause .	28
5. Open the Home Connect app on your smartphone or tablet PC and select Connect to add your new appliance.	28
Note:	28
6. If your appliance is not shown automatically, select Appliance search and then Connect an appliance in the Home Connect app.	28
7. Carry out the last steps in the Home Connect app to connect your appliance.	28
8. Press Remote Start briefly to exit the Home Connect settings.	29
Note:	29
Activating/deactivating Wi-Fi	29
You can switch the Home Connect function on your appliance on or off permanently at any time.	29
1. Switch the appliance on.	29
2. Press and hold Remote Start for at least 3 seconds.	29
3. Turn the program selector to position 4.	29
4. Press Start/Pause .	29
5. Press Remote Start briefly to exit the Home Connect settings.	29
Notes	29
Resetting your network settings	29
You can clear the network settings and break the connection to your smartphone or tablet PC by resetting the network settings.	29
1. Switch the appliance on.	29
2. Press and hold Remote Start for at least 3 seconds.	29
3. Turn the program selector to position 5.	29
4. Press Start/Pause .	29
5. Press Start/Pause to confirm.	29
6. Press Remote Start briefly to exit the Home Connect settings.	29
Notes	29
Updating the software	30
You can update the Home Connect software on your appliance. As soon as a new update is available, —˜š (update) will appear on the display.	30
You can install the update directly via the message on the display or, alternatively, you can do this manually.	30
1. Switch the appliance on.	30
2. Press and hold Remote Start for at least 3 seconds.	30
3. Turn the program selector to position 6.	30
4. Press Start/Pause .	30
5. Press Start/Pause to confirm.	30
6. Press Remote Start briefly to exit the Home Connect settings.	30
Information on data protection	30
When your appliance is connected to a WLAN network that is connected to the Internet for the first time, your appliance transmits the following categories of data to the Home Connect server (initial registration):	30
This initial registration prepares the Home Connect functions for use and is only required when you want to use these Home Connect functions for the first time.	30
Note:	30
Declaration of Conformity	30
BSH Home Appliances Group hereby declares that the appliance which features Home Connect functionality is in accordance with the essential requirements and other relevant provisions of the following Directives.	30
Wi-Fi® Module FCC/IC Statements	30
Model: COM1	30
FCC ID: 2AHES-COMGEN1	30
IC: 21152-COMGEN1	30
The Home Connect module is a communication device designed to provide communication between appliances and smart devices.	30
This module is integrated at the factory, under direct control of B/S/H Home Appliances Corporation, and is not user serviceable or upgradable. At least 20cm separation distance should be maintained from device to user.	30
FCC COMPLIANCE STATEMENT	30
9 CAUTION	30
INDUSTRY CANADA STATEMENT	30
Laundry	31
Preparing the laundry	31
NOTICE:	31
Sorting the laundry	31
Sort laundry items according to color, degree of soiling and recommended wash temperature range.	31
Wash white items separately from colored items. Otherwise, white items may tend to become grey.	31
Observe laundry care labels	31
Check the care labels on each laundry item prior to washing. Choose an appropriate wash cycle that does not exceed the temperature recommended.	31
Determining degree of soiling	31
Identifying and treating stains	32
For mild and recent stains the Stains button for food based grease/oils, blood, red wine and grass can be used. For more stubborn and set in stains the below methods can be of help.	32
Removing stains	32
Laundry detergents and additives	33
Adding the correct amount of HE detergent	33
9 WARNING	33
Avoid overuse of detergent.	33
Measure out the detergent according to:	33
Too much detergent	33
Too little detergent	33
The fabric care label is important for selecting the correct detergent, temperature and treatment of the laundry.	33
If desired you can visit the following sites for additional information on detergents and fabric care.	33
~ www.textileaffairs.com or www.cleanright.eu	33
Saving energy and reduce detergent	33
For light and normal soiling, you can save energy (lower washing temperature) and detergent.	33
NOTICE:	33
Program selection table	34
Tips	34
Starching	35
NOTICE:	35
Starching is possible in all wash programs if liquid starch is used. Measure starch into compartment M in accordance with the manufacturer's instructions (clean first if necessary).	35
Dyeing/bleaching	35
Dye should only be used in normal household quantities. Salt may damage stainless steel. Always follow the dye manufacturer's instructions.	35
Do not use the washing machine to bleach clothes.	35
Soaking	35
1. Pour soaking agent/detergent into compartment II in accordance with the manufacturer's instructions.	35
2. Turn the program selector to Cotton program and select Cold temperature.	35
3. Press Start/Pause.	35
4. After approximately ten minutes, press Start/Pause.	35
5. After the required soaking time, press Start/Pause again to continue or change the program.	35
NOTICES	35
Optional program settings	36
At the factory, temperature and spin speed options, and cycle duration (\	36
EcoPerfect	36
Energy optimised washing by reducing the temperature while achieving a washing result that is consistent with the selected program, without the EcoPerfect setting.	36
Prewash	36
For heavily soiled washing. Pour 1/3 of normal detergent amount into pre-wash chamber I and remaining 2/3 into main wash chamber II.	36
Rinse Plus	36
This feature adds additional rinses to selected program which is helpful for locations with soft water supplies or to generally improve rinsing results. It will increase the program duration.	36
Remote Start	36
Briefly pressing the Remote Start button activates or deactivates the Remote start function. Activating the Remote start function enables the appliance to be started remotely via the Home Connect app.	36
NOTICES	36
Pressing and holding the Remote Start button for at least 3 seconds enters Home Connect settings.	36
Finish in	36
The program end (Finished in) time can be set in one hour increments to a maximum of 24 h (hours). After selecting the desired washing program (at the dial) but before pressing the Start/Pause button, press the Finish in button until the desired time...	36
NOTICE:	36
Here is an example of a 1hr:30min cycle time and an 8 h Finish in time.	36
8 h is displayed (until the Energy-saving mode activates) and counts down (approximately 6hr:30min) until the washing cycle begins (at 1hr:30min) then the cycle duration 1:30 is displayed and began. Total time approximately 8 hours.	36
Spin Speed	36
Before and during the cycle, you can change the spin speed range depending on the cycle progress.	36
Touch the appropriate button until the desired setting is displayed.	36
No Spin: This option eliminates the final spin and the load remains saturated with the final rinse water. The pump is activated to remove all residual water.	36
~ Program selection table; Page 34	36
Temperature	36
Before and during the cycle, you can change the default temperature range depending on the cycle progress.	36
Press the appropriate button until the desired setting is displayed.	36
The maximum temperature range that can be set depends on the cycle selected.	36
~ Program selection table; Page 34	36
SpeedPerfect	36
For washing in a shorter time with a washing result comparable to that of the standard program.	36
NOTICE:	36
Stains	36
There are four types of stain to choose from:	36
The washer adjusts the average washing temperature, drum movement and soaking time to the specific type of stain. Hot or cold water, gentle or intensive washing and long or short soaking ensure that the wash-program sequence is specially adapted to e...	36
NOTICE:	36
Appliance settings	37
Child lock	37
You can secure the appliance against inadvertent changing of the set functions. To do this, activate the Child lock after cycle start.	37
To Activate/Deactivate, press Finish in M and N for approximately 3 seconds. In the display field, you will see the D symbol light indicating the Child lock is active.	37
NOTICE:	37
Activating setting mode	37
In order to change the default appliance settings described below, you will first need to enter or activate setting mode.	37
1. Switch on the appliance. The indicator lamp of the program on position 1 (() lights up.	37
2. Press and hold Temperature button and, at the same time, turn the program selector to position 2 (0).	37
3. Release Temperature button.	37

Match case Limit results 1 per page

Liquid detergent insert

To measure liquid detergent:

Pull out the detergent dispenser tray.

Push the liquid detergent insert forward and down as

shown.

Pour liquid detergent into the chamber and do not

exceed the maximum mark.

Reinsert the tray into its compartment.

NOTICE:

Do not use the liquid detergent insert with gel-

type detergents and powdered detergents or for cycles

with pre-wash or selected "Finish in" time.

Starting the program

Press the

Start/Pause

button. Indicator lamp lights up

and the program starts.

NOTICE:

If you want to protect the cycle against

inadvertent adjustment, select the Child lock.

Child lock; Page 37

The display panel shows the "Finish in" time before the

program starts or the program length and the program

progress symbols when the washing program has

started.

Display area; Page 21

Foam detection

If you use too much detergent, too much foam may be

formed during the wash cycle. The symbol

lights up.

Foam may be also leaking out from the detergent

drawer. In order to remove the foam, the appliance

automatically activates additional rinse cycles. This

extends program duration.

NOTICE:

To prevent excess foaming use less detergent

in subsequent wash loads.

Selecting a different program

If you have inadvertently started the wrong program, you

can change this as follows:

Press

Start/Pause

Select another program.

Press

Start/Pause

. The new cycle starts from the

beginning.

Pausing/Adding a garment to the cycle

Pausing the wash cycle can be useful for several

purposes.

e.g. for soaking

Soaking; Page 35

Press

Start/Pause

. The indicator lamp

is blinking.

Wash load will soak in water until continued by pressing

Start/Pause

For adding a garment after the cycle begins.

Press

Start/Pause

. Door will unlock when safe to do

so.

Open door carefully and add or remove laundry item.

NOTICE:

You can do this as long as the

Start/Pause

indicator flashes and it is safe to do so.

Close door.

Press

Start/Pause

The cycle continues.

NOTICE:

If the cycle is paused but the door will not

unlock it could be for safety reasons (high water level,

water temperature or drum speed).

Cancel program

For cycles with a high temperature:

Press

Start/Pause

Cool the laundry off: Select

Rinse

Press

Start/Pause

For cycles with a low temperature:

Press

Start/Pause

Select

Spin/Drain

and

Spin Speed

option to

No Spin

Press

Start/Pause

Program end

‹

appears in the display field and the Start/Pause

button indicator lamp is off.

NOTICE:

If this symbol

appears in the display, the

washer has detected too much foam and it automatically

adds an additional rinse cycles to remove the foam.

Use less detergent the next time you run the washer with

the similar load.