Home » Brother International Manuals » Sewing Machines » Brother International KE-435C » Manual Viewer

Brother International KE-435C Instruction Manual - English - Page 57

CHANGING FUNCTIONS USING THE DIP SWITCHES, 12-1. Operation panel DIP switches

Get Brother International KE-435C PDF manuals and user guides

View all Brother International KE-435C manuals

Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

12. CHANGING FUNCTIONS USING THE DIP SWITCHES 12. CHANGING FUNCTIONS USING THE DIP SWITCHES 12-1. Operation panel DIP switches The functions shown in the table below can be changed by means of these DIP switches (1). * All DIP switches are set to OFF at the time of shipment. Note: Always turn off the power before setting the DIP switches. Switch DIPA-1 DIPA-2 DIPA-3 DIPA-4 DIPA-5 DIPA-6 DIPA-7 DIPA-8 2586Q 0176Q Motion when set to ON Presser does not automatically lift after sewing is completed. Pedal mode is switched. See "14. Setting the presser mode" User program mode is available. − The presser does not rise automatically when a split is found. Displays the enlargement/reduction ratio in millimeter units instead of as a percentage. (After changing this setting, be sure to carry out the auto-clear operation by referring to page 46.) Enlargement of pattern size is not available. Program number is fixed. KE-434C,435C 51

Section	Page
front	1
SAFETY INSTRUCTIONS	2
2. Notes on safety	3
3. Warning labels	5
CONTENTS	6
1. NAME OF EACH PART	7
2. SPECIFICATIONS	8
2-1. Specifications	8
2-2. Examples of sewing patterns	9
3. INSTALLATION	10
3-1. Power table	10
3-2. Installing the control box	11
3-3. Installing the rubber cushions	12
3-4. Installing the oil pan	12
3-5. Installing the cushions	12
3-6. Installing the switching plate	13
3-7. Installing the machine head	13
3-8. Installing the head rest	14
3-9. Installing the liquid cooling tank, optional	14
3-10. Installing the operation panel	15
3-11. Connecting the ground wire	15
3-12. Connecting the cords	16
3-13. Piping (for pneumatic)	19
3-14. Installing the belt cover	22
3-15. Installing the foot switch	22
3-16. Installing the needle sub plate	23
3-17. Installing the spool stand	24
3-18. Installing the eye guard	24
4. LUBRICATION	25
4-1. Lubrication points	25
5. OPERATION	26
5-1. Name and function of each operation panel item	26
5-2. Operating procedure	28
5-3. Operating the foot switch	30
5-4. Operating the emergency stop switch	31
5-5. Operating the thread wiper switch (KE-435C)	31
6. CHECKING THE SEWING PATTERN	32
7. CORRECT USE	33
7-1. Selecting the needle and thread	33
7-2. Installing the needle	33
7-3. Threading the upper thread	33
7-4. Winding the lower thread	34
7-5. Replacing the bobbin case and threading the thread	35
7-6. Thread tension	35
8. SEWING	38
9. MAINTENANCE AND INSPECTION	39
9-1. Checking the needle	39
9-2. Cleaning the rotary hook	39
9-3. Lubrication	40
9-4. Draining the oil	41
9-5. Cleaning the control box air inlet port	41
9-6. Cleaning the air holes of belt cover and frame side cover	41
9-7. Cleaning the eye guard	41
10. STANDARD ADJUSTMENTS	42
10-1. Adjusting the needle bar height	42
10-2. Adjusting the needle bar lift amount	42
10-3. Adjusting the driver needle guard	43
10-4. Adjusting the needle clearance	43
10-5. Adjusting the shuttle race thread guide	43
10-6. Adjusting the thread take-up amount	44
10-7. Adjusting the movable knife	45
10-8. Adjusting the work clamp lift amount	48
10-9. Work clamp interchangeability	49
10-10. Adjusting the needle up stop position	49
10-11. Adjusting the thread wiper	50
10-12. Checking the input sensor and DIP switch input	51
10-13. Checking the input voltage	52
10-14. Clearing all memory settings	52
10-15. Moving stitch patterns	53
10-16. Adjustment of air pressure (for pneumatic)	54
10-17. Adjustment of inner clamping device	54
10-18. Work clamp adjustment (KE-435C)	55
10-19. Changing the work clamp lift (KE-435C)	55
11. USING THE COUNTERS	56
11-1. Using the bobbin thread counter	56
11-2. Using the production counter	56
12. CHANGING FUNCTIONS USING THE DIP SWITCHES	57
12-1. Operation panel DIP switches	57
12-2. DIP switches inside the control box	58
12-3. Using user programs	59
13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES	61
13-1. Using the cycle sewing function	64
14. SETTING THE WORK CLAMP MODE	66
14-1. Setting solenoid work clamp mode	66
14-2. Setting pneumatic work clamp mode	66
14-3. Light work clamp	68
14-4. Setting reverse work clamp mode	69
15. TABLE OF ERROR CODES	70
16. GAUGE PARTS LIST ACCORDING TO SUBCLASSES	72
17. MAKING THE FEED PLATE AND WORK CLAMP PLATE FOR INNER CLAMPING DEVICE	75
17-1. Sewing area	75
17-2. How to make a sewing pattern	75
17-3. How to make the feed plate	76
17-4. How to make the work clamp plate	77
17-5. Replacing the work clamp crank and work clamp plate holder	78
18. TROUBLESHOOTING	79
19. OPTIONAL PARTS	82