Brother International SB7050E Operation Manual - Page 13

Needle and embroidery foot, Right-side/rear view

Get Brother International SB7050E PDF manuals and user guides View all Brother International SB7050E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Needle and embroidery foot section Right-side/rear view a Thread guide disk (page 40) Pass the thread through the thread guide disk when using the needle threader to thread the needle. b Needle bar thread guide (page 40) Pass the upper thread through the needle bar thread guide. c Needle plate When the needle is lowered, it enters the hole in the needle plate. d Needle plate cover (page 78) Remove the needle plate cover to clean the bobbin case and race. e Bobbin cover/bobbin case (page 35) Remove the bobbin cover, and then insert the bobbin into the bobbin case. f Embroidery foot "Q" (page 80) This presser foot is used for embroidering. a Handle Carry the machine by its handle when transporting the machine. b Handwheel (page 38) Turn the handwheel toward you (counterclockwise) to raise and lower the needle. c Embroidery card slot (page 55) Insert the embroidery card. d USB port (for a USB flash drive (USB flash memory)) In order to import patterns from a USB flash drive (USB flash memory), plug the USB media directly into the USB port. e Air vent The air vent allows the air surrounding the motor to be exchanged. Do not cover the air vent while the machine is being used. f Main power switch (page 18) Use the main power switch to turn the machine on and off. g Power supply jack (page 18) Insert the plug on the power supply cord into the power supply jack. Memo z Refer to pages 10 through 13 while you are learning to use your machine. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
11
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Needle and embroidery foot
section
a
Thread guide disk (page 40)
Pass the thread through the thread guide disk when
using the needle threader to thread the needle.
b
Needle bar thread guide (page 40)
Pass the upper thread through the needle bar thread
guide.
c
Needle plate
When the needle is lowered, it enters the hole in the
needle plate.
d
Needle plate cover (page 78)
Remove the needle plate cover to clean the bobbin case
and race.
e
Bobbin cover/bobbin case (page 35)
Remove the bobbin cover, and then insert the bobbin
into the bobbin case.
f
Embroidery foot “Q” (page 80)
This presser foot is used for embroidering.
Right-side/rear view
a
Handle
Carry the machine by its handle when transporting the
machine.
b
Handwheel (page 38)
Turn the handwheel toward you (counterclockwise) to
raise and lower the needle.
c
Embroidery card slot (page 55)
Insert the embroidery card.
d
USB port (for a USB flash drive (USB flash memory))
In order to import patterns from a USB flash drive (USB
flash memory), plug the USB media directly into the
USB port.
e
Air vent
The air vent allows the air surrounding the motor to be
exchanged. Do not cover the air vent while the machine
is being used.
f
Main power switch (page 18)
Use the main power switch to turn the
machine on and
off.
g
Power supply jack (page 18)
Insert the plug on the power supply cord into the power
supply jack.
Memo
Refer to pages 10 through 13 while you are
learning to use your machine.