Canon 600 Optura Instruction Manual - Page 58

Setting the Audio Output - eos

Get Canon 600 - Optura 4.3MP MiniDV Camcorder PDF manuals and user guides
UPC - 013803050738
View all Canon 600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Setting the Audio Output E MENU AUDIO MONITOR When you play back a tape that was recorded in 12 bit mode, you can set the audio output to play stereo 1 (the original sound), stereo 2 (any new sound, dubbed to the tape after recording), or mix the balance between the two. To simply choose stereo1 or stereo2, you do not need to release the fixed level (skip step number 2 below). 1. Set the camera to VCR mode. 2. Release the fixed level (for audio mixing only). (see p. 25) MIX SELECT••VARIABLE a) Open the VCR menu and point the arrow at MIX SELECT. b) Select the VARIABLE setting and close the menu. 3. Choose the output. You can only choose the output using the wireless controller. a) Press the wireless controller's AUDIO MONITOR button to display "STEREO1", "STEREO2", and "MIX", each in turn. STEREO1 STEREO2 MIX • Your choice is selected approximately 4 seconds after you last pressed the button. If you choose "MIX" you can go on to mix the balance. • Use the cursor keys to choose the mix ST - 1 ST-2 balance. Notes: • When you have chosen the output, "STEREO1", "STEREO2", or "MIX" is shown in the top left of the display. If you turn the power off the output (and display) is set to "STEREO1" • You cannot mix the balance without first releasing the fixed level: the camera will show "FIXED" in the display. 58 Additional Information

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
MIX SELECT••VARIABLE
When you play back a tape that was recorded in 12 bit mode, you can set the
audio output to play stereo 1 (the original sound), stereo 2 (any new sound,
dubbed to the tape after recording), or mix the balance between the two.
To simply choose stereo1 or stereo2, you do not need to release the fixed level
(skip step number 2 below).
1.
Set the camera to VCR mode.
2.
Release the fixed level (for audio mixing only).
Setting the Audio Output
Additional
Information
58
E
MENU
AUDIO
MONITOR
(see p. 25)
a) Open the VCR menu and point the arrow at MIX SELECT.
b) Select the VARIABLE setting and close the menu.
3. Choose the output.
You can only choose the output using the wireless controller.
a) Press the wireless controller’s AUDIO
MONITOR button to display “STEREO1”,
“STEREO2”, and “MIX”, each in turn.
•
Your choice is selected approximately 4
seconds after you last pressed the button.
If you choose “MIX” you can go on to mix the
balance.
•
Use the
cursor keys to choose the mix
balance.
Notes:
•
When you have chosen the output, “STEREO1”, “STEREO2”, or “MIX” is
shown in the top left of the display. If you turn the power off the output (and
display) is set to “STEREO1”
•
You cannot mix the balance without first releasing the fixed level: the camera
will show “FIXED” in the display.
STEREO1
MIX
STEREO2
ST–1
ST–2