Cisco WS-C3750G-24TS-S1U Getting Started Guide - Page 22

In Case of Difficulty, Troubleshooting Express Setup

Get Cisco WS-C3750G-24TS-S1U - Catalyst Switch - Stackable PDF manuals and user guides
UPC - 746320953410
View all Cisco WS-C3750G-24TS-S1U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

7 In Case of Difficulty If you experience difficulty, help is available in this section and also on Cisco.com. This section includes Express Setup troubleshooting, how to reset the switch, how to access help online, and where to find more information. Troubleshooting Express Setup If Express Setup does not run, or if the Express Setup page does not appear in your browser: • Did you verify that POST successfully ran before starting Express Setup? If not, make sure that only the SYST and STAT LEDs are green before pressing the Mode button to enter the Express Setup mode. • Did you press the Mode button while the switch was still running POST? If yes, wait until POST completes. Power cycle the switch. Wait until POST completes. Confirm that the SYST and STAT LEDs are green. Press the Mode button to enter Express Setup mode. • Did you try to continue without confirming Verify that all LEDs above the Mode button are that the switch was in Express Setup mode? green. (The RPS LED is off.) If necessary, press the Mode button to enter Express Setup mode. • Does your PC have a static IP address? If yes, before connecting to the switch, change your PC settings to temporarily use DHCP. • Did you connect a crossover cable instead of If yes, connect a straight-through cable to an a straight-through Ethernet cable between a Ethernet port on the switch and the PC. Wait 30 switch port and the Ethernet port of the PC? seconds before you enter 10.0.0.1 in the browser. • Did you connect the Ethernet cable to the console port instead of to a 10/100 or 10/100/1000 Ethernet port on the switch? If yes, disconnect the cable from the console port. Then connect the cable to an Ethernet port on the switch and the PC. Wait 30 seconds before you enter 10.0.0.1 in the browser. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
22
7
In Case of Difficulty
If you experience difficulty, help is available in this section and also on Cisco.com. This section
includes Express Setup troubleshooting, how to reset the switch, how to access help online, and where
to find more information.
Troubleshooting Express Setup
If Express Setup does not run, or if the Express Setup page does not appear in your browser:
•
Did you verify that POST successfully ran
before starting Express Setup?
If not, make sure that only the SYST and STAT
LEDs are green before pressing the Mode button
to enter the Express Setup mode.
•
Did you press the Mode button while the
switch was still running POST?
If yes, wait until POST completes. Power cycle the
switch. Wait until POST completes. Confirm that
the SYST and STAT LEDs are green. Press the
Mode button to enter Express Setup mode.
•
Did you try to continue without confirming
that the switch was in Express Setup mode?
Verify that all LEDs above the Mode button are
green. (The RPS LED is off.) If necessary, press
the Mode button to enter Express Setup mode.
•
Does your PC have a static IP address?
If yes, before connecting to the switch, change
your PC settings to temporarily use DHCP.
•
Did you connect a crossover cable instead of
a straight-through Ethernet cable between a
switch port and the Ethernet port of the PC?
If yes, connect a straight-through cable to an
Ethernet port on the switch and the PC. Wait 30
seconds before you enter
10.0.0.1
in the browser.
•
Did you connect the Ethernet cable to the
console port instead of to a 10/100 or
10/100/1000 Ethernet port on the switch?
If yes, disconnect the cable from the console port.
Then connect the cable to an Ethernet port on the
switch and the PC. Wait 30 seconds before you
enter
10.0.0.1
in the browser.