Compaq 2230s HP Compaq 2230s Notebook PC - Maintenance and Service Guide - Page 69

Reverse this procedure to install the system board., Use the optical drive connector

Get Compaq 2230s - Notebook PC PDF manuals and user guides View all Compaq 2230s manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Remove the system board: 1. Remove the Torx T8M2.5×6.0 slotted screw that secures the system board to the base enclosure. The screw is located by the optical drive connector, 2. Flex the left side of the base enclosure until the USB, RJ-45, and RJ-11 jacks 1 clear the openings in the base enclosure. 3. Use the optical drive connector 2 to lift the left side of the system board 3 until it rests at an angle. 4. Remove the system board from the base enclosure by pulling it away at an angle 4. Reverse this procedure to install the system board. Removal and replacement procedures 4-35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Removal and replacement procedures
4–35
Remove the system board:
1. Remove the Torx T8M2.5×6.0 slotted screw that secures the system board to the base enclosure. The screw is
located by the optical drive connector,
2. Flex the left side of the base enclosure until the USB, RJ-45, and RJ-11 jacks
1
clear the openings in the base
enclosure.
3. Use the optical drive connector
2
to lift the left side of the system board
3
until it rests at an angle.
4. Remove the system board from the base enclosure by pulling it away at an angle
4
.
Reverse this procedure to install the system board.