Compaq Armada e500s Compaq ArmadaStation EM Maintenance and Service Guide
Compaq Armada e500s - Notebook PC Manual
View all Compaq Armada e500s manuals
Add to My Manuals
Save this manual to your list of manuals |
Compaq Armada e500s manual content summary:
- Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 1
Compaq ArmadaStation EM Maintenance and Service Guide - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 2
guide may be photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation. 1999 Compaq Computer Corporation. All rights reserved. Printed in the U.S.A., U.K., Singapore, and Taiwan. COMPAQ and ARMADA . MAINTENANCE AND SERVICE GUIDE Compaq Expansion Base First - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 3
Lock...1-8 PCI Expansion Boards...1-8 chapter 2 TROUBLESHOOTING Before Replacing Parts ...2-1 Problems and Solutions ...2-2 chapter 3 ILLUSTRATED PARTS Drives...4-3 Grounding Methods...4-3 Grounding Workstations ...4-4 Grounding Equipment ...4-4 Recommended Materials and Equipment 4-5 4.2 Service - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 4
...5-12 5.9 Half-Height Bay...5-14 Installing a Half-Height Drive...5-14 5.10 Left Speaker ...5-23 5.11 Control Bay ...5-24 5.12 Control Panel...5-26 5.13 Mechanism Assembly...5-27 5.14 Power Supply ...5-29 5.15 Backplane...5-31 chapter 6 SPECIFICATIONS ...6-1 appendix 1 CONNECTOR PIN ASSIGNMENTS - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 5
information or specific instructions. NOTE: Text set off in this manner presents commentary, sidelights, or interesting points of information. Technician Notes ! WARNING: Only authorized technicians trained by Compaq should attempt to repair this equipment. All troubleshooting and repair procedures - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 6
Information The following documentation is available to support the ArmadaStation EM: s Compaq ArmadaStation EM documentation set s Service training guides s Compaq Service Advisories and Bulletins s Compaq QuickFind s Compaq Service Quick Reference Guide s Compaq Internet site at http://www - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 7
ArmadaStation EM provides fully integrated desktop capabilities for the Compaq Armada E and M Series of Personal Computers. The ArmadaStation EM eliminates the need to disconnect external devices when you remove the computer. NOTE: The Armada M300 computer requires the Mobile Expansion Unit (MEU) to - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 8
half-sized 32-bit PCI slots. A monitor support cover capable of supporting up to 75 pounds (34 kilograms) also release latch to prevent access to the computer manual eject button and PCI slots, and disables the Universal Serial Bus (USB) connectors (2) s Stereo line-in jack s Microphone out jack s - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 9
Description Function 1 Alignment guides 2 Retaining latch 3 Supports a removable DVD-ROM drive, CD-ROM drive, diskette drive, SuperDisk LS-120 drive, hard drive, or extra battery pack. 11 Top MultiBay Supports a removable DVD-ROM drive, CD-ROM drive, SuperDisk LS-120 drive, or hard drive - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 10
sound plays in stereo from both ArmadaStation EM speakers. 5 Microphone jack Connects a single sound channel microphone. The sound plays from both ArmadaStation EM speakers. 6 USB connectors (2) Connect universal serial bus (USB) devices. 7 Keylock Locks the computer to the ArmadaStation EM - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 11
. 11 U-bolt Attaches an optional heavy-duty cable and lock to secure the ArmadaStation EM to a fixed object. 12 Monitor latch slot Attaches the monitor support cover rear latch. Product Description 1-5 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 12
, including hard drives (installed into a MultiBay hard drive adapter), CD-ROM drives, DVD-ROM drives, diskette drives (bottom MultiBay only), and SuperDisk LS-120 drives. The bottom MultiBay can also be used to charge MultiBay battery packs. The ArmadaStation EM MultiBays support the following - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 13
EM. The half-height bay supports any standard half-height drive or a half-height MultiBay adapter. Security Lock The ArmadaStation EM features a security lock that allows all computer and ArmadaStation EM resources (hard drives, diskette drives, CD-ROM drives, PCI expansion boards) to be - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 14
the problem is solved. Before Replacing Parts When troubleshooting a problem, check the following list for possible solutions before replacing parts: s Verify that cables are connected properly to the suspected defective parts. s Verify that all required device drivers are installed. Troubleshooting - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 15
the ArmadaStation EM manual release lever to the right. Table 2-2 Solving Expansion Board Problems Problem Probable Cause drivers for the expansion board are not installed. Reinstall the expansion board. Obtain the necessary drivers from the expansion board manufacturer. 2-2 Troubleshooting - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 16
Device is not plug and play. For Windows 95 or Windows 98: Double-click the Add New Hardware icon in Control Panel for help installing the device. You can also use Computer Setup to install a new device. Choose Tools, Adding a Legacy Device, and follow onscreen instructions. Troubleshooting 2-3 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 17
monitor. monitor. Press the Fn+F4 hotkeys to switch the image to the computer screen. Display on the external monitor is distorted. Incorrect display device drivers Select Start→ Settings→ Control Panel→ are installed or incorrect Display icon, and set the display type and resolution is set - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 18
3 chapter ILLUSTRATED PARTS CATALOG This chapter provides an illustrated parts breakdown and a reference for spare part numbers for the Compaq ArmadaStation EM. 3.1 Serial Number Location When ordering parts or requesting information, provide the ArmadaStation EM serial number located on the right - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 19
3.2 Compaq ArmadaStation EM Components Figure 3-2. Compaq ArmadaStation EM Components Illustrated Parts Catalog 3-2 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 20
Table 3-1 Spare Parts: Compaq ArmadaStation EM Components Item Description Spare Part Number 1 Top cover 155269-001 Cable Kit, includes: 6a Hard drive cable 6b Diskette drive cable 6c CD-ROM drive/audio cable Hard drive cable (7"; not illustrated) Drive power cable (not illustrated) - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 21
3.3 Plastics Kit Components Figure 3-3. Plastics Kit Components Table 3-2 Plastics Kit Components Spare Part Number 155277-001 Item Description 1 Connector cover 2 MultiBay buttons (2) Illustrated Parts Catalog 3-4 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 22
Option Cable Kit Figure 3-4. Cable Kit Components Table 3-3 MultiBay Option Cable Kit Components Spare Part Number 298038-001 Item Description 1 Hard drive cable 2 Hard drive cable (7" ) 3 Drive power cable 4 CD-ROM drive/audio cable 5 Diskette drive cable Illustrated Parts Catalog 3-5 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 23
3.5 Miscellaneous Table 3-4 Spare Parts: Miscellaneous (not illustrated) Description Spare Part Number Compaq ArmadaStation EM Maintenance and Service Guide 163487-001 Compaq ArmadaStation EM Screw Kit 155278-001 Carbon keyboard 118003-XX8 Carbon monitor 307710-023 PCI CardBus reader - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 24
service information for the Compaq Expansion base. Adherence to the procedures and precautions described in this chapter is essential for proper service into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 25
Generating Static Table 4-1 shows how different activities generate static electricity and at different electrostatic voltage levels. Table 4-1 Typical Electrostatic Voltages Relative Humidity Event 10% 40% Walking across carpet Walking across vinyl floor Motions of bench worker Removing DIPS - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 26
static damage to drives, follow these precautions: s Handle drives gently, using static-guarding techniques. s Store drives in the hard drive carrying case. Do not use the MultiBay device carrying case. s Avoid dropping drives from any height onto any surface. s Handle drives on surfaces that - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 27
and assemblies by the case or PCB laminate. service kit with a static-dissipative vinyl pouch that folds out into a work mat. Also, use a wrist strap and a ground cord for the work surface. Ground the cord to the chassis of the equipment undergoing test or repair of shoes or boots. On conductive - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 28
foam s Conductive tabletop workstations with ground cord of one megohm resistance s Static-dissipative table or floor mats with hard tie to ground s Field service kits s Static awareness labels s Wrist straps and footwear straps providing one megohm +/- 10% resistance s Material handling packages - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 29
needed to service the Compaq Expansion Base: s Phillips screwdriver (for bezel cage removal) s Torx T-10 screwdriver (for tray, top cover, left speaker, control bay, control panel, and mechanism assembly removal procedures) s Torx T-15 screwdriver (for PCI expansion board installation procedures and - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 30
connector. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing the cables, and ensure ; they can tear easily. CAUTION: When servicing the Compaq Expansion Base, ensure that cables are placed in instructions. Removal and Replacement Preliminaries 4-7 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 31
5 chapter REMOVAL AND REPLACEMENT PROCEDURES This chapter presents the removal and replacement procedures for the Compaq ArmadaStation EM. 5.1 Serial Number The serial number should be reported to Compaq when requesting information or ordering spare parts. The serial number is located on the right - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 32
Sequence Chart Use the chart below to determine the section number and disassembly sequence for removing components from the Compaq ArmadaStation EM. 5.3 Preparing the Expansion Base for Disassembly 5.4 External Components Expansion Base Feet Tray 5.5 Connector Cover 5.6 Rear Bezel 5.7 PCI - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 33
cord from the wall outlet (Figure 5-3). 5. Disconnect the power cord from the expansion base . Figure 5-3. Disconnecting the Expansion Base 6. Disconnect any external devices. 7. If installed, remove any MultiBay devices from the expansion base MultiBays. Removal and Replacement Procedures 5-3 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 34
of the expansion base. This includes: s Expansion base feet s Tray Expansion Base Feet The feet for the expansion base are adhesive-backed rubber pads. Install the feet by removing the protective covering from the adhesive back and placing the feet in their positions on the bottom of the expansion - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 35
the retaining latch (Figure 5-5). 4. Pull forward on the retaining latch to remove the tray. Figure 5-5. Removing the Tray Reverse the removal procedure described above to install the tray. Removal and Replacement Procedures 5-5 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 36
faces forward. 3. Slide the connector cover to the left and remove it (Figure 5-6). Figure 5-6. Removing the Connector Cover Reverse the removal procedure described above to install the connector cover. 5-6 Removal and Replacement Procedures - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 37
5.6 Rear Bezel 1. Prepare the expansion base for disassembly (Section 5.3). 2. Remove the connector cover (Section 5.5). 3. Slide the rear bezel release latch to the left (Figure 5-7). 4. Swing the bottom edge of the rear bezel forward and up until it disengages . Figure 5-7. Removing the Rear - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 38
the expansion base, releases and allows the computer to be manually undocked. Figure 5-8. Sliding the Manual Release Lever Reverse the removal procedure described above to install the rear bezel. Before installing the rear bezel, make sure the manual release lever is positioned as far to the left as - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 39
base provides three slots for 32- or 64-bit PCI expansion boards. The expansion base supports half-sized expansion boards in slots , and ; a full-sized expansion board can be installed in slot (Figure 5-9). Figure 5-9. Locating the Expansion Slots For additional information, consult the - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 40
4. Remove the screw that secures the expansion slot cover to the base cover (Figure 5-10). NOTE: Retain the expansion slot cover and screw. They will be needed if the expansion board is removed from the expansion base. 5. Remove the expansion slot cover . Figure 5-10. Removing the Expansion Slot - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 41
installing the screw removed in Step 4. Figure 5-11. Installing an Expansion Board Reverse the installation an expansion board has been installed, its internal connector can information. IMPORTANT: If a PCI CardBus Reader has been installed, PC Cards must be inserted label side down into the - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 42
5.8 Top Cover 1. Prepare the expansion base for disassembly (Section 5.3). 2. Remove the tray (Section 5.4). 3. Remove the connector cover (Section 5.5). 4. Remove the rear bezel (Section 5.6). 5. Remove the five screws that secure the top cover to the base cover (Figure 5-12). Figure 5-12. Removing - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 43
6. Swing the top cover up and forward to remove it (Figure 5-13). Figure 5-13. Removing the Top Cover Reverse the removal procedure described above to install the top cover. Removal and Replacement Procedures 5-13 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 44
half-height bay, located on the left side of the expansion base. This bay supports any standard half-height drive, such as a diskette or hard drive. Installing a Half-Height Drive 1. Prepare the expansion base for disassembly (Section 5.3). 2. Remove the tray (Section 5.4). 3. Remove the connector - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 45
8. Remove the half-height bay blank bezel cover from the bezel cage (Figure 5-15). Figure 5-15. Removing the Half-Height Bay Blank Bezel Cover Removal and Replacement Procedures 5-15 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 46
, remove the screws from the half-height drive to be installed (Figure 5-16). NOTE: The half-height drive should have two screws installed in each side. If these screws are missing, appropriate-sized screws must be obtained to secure the half-height drive to the bezel cage. Figure 5-16. Removing - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 47
bezel cage should be aligned so the "L" and "LEFT" indicators can be read when the half-height drive is installed in the expansion base left half-height bay. 11. Install the four screws that secure the half-height drive to the bezel cage. Figure 5-17. Attaching the Bezel Cage to the Half-Height - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 48
the following sections for information on attaching the appropriate cables to the connectors on the half-height drive and the expansion base. Refer to the documentation that came with the half-height drive for information about which expansion base connectors to use. 12. Connect the half-height bay - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 49
13. If a diskette drive is being installed, connect the diskette drive cable to the diskette drive connector (Figure 5-19). Figure 5-19. Connecting the Diskette Drive Cable Removal and Replacement Procedures 5-19 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 50
14. If a hard drive is being installed, connect the hard drive cable to the hard drive connector (Figure 5-20). Figure 5-20. Connecting the Hard Drive Cable 5-20 Removal and Replacement Procedures - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 51
15. If a CD- or DVD-ROM drive is being installed, connect the CD-ROM drive/audio cable to the connector (Figure 5-21). Figure 5-21. Connecting the CD-ROM Drive/Audio Cable Removal and Replacement Procedures 5-21 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 52
16. Insert the half-height drive assembly into the base cover (Figure 5-22). 17. Install the three screws that secure the bezel cage to the base cover. Figure 5-22. Installing a Half-Height Drive Reverse the installation procedure described above to remove a half-height drive. 5-22 Removal and - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 53
the MultiBay (Figure 5-23). 8. Remove the left speaker from the base assembly. Figure 5-23. Removing the Left Speaker Reverse the removal procedure described above to install the left speaker. Removal and Replacement Procedures 5-23 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 54
of the expansion base. These MultiBays support all MultiBay devices supported by the Compaq Armada Series of Personal Computers. 1. Prepare Section 5.8). 6. Disconnect the left speaker , CD-ROM/audio , hard drive , and diskette drive cables from the MultiBay (Figure 5-24). Figure 5-24. - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 55
removed in this step are two different sizes: four screws are Torx T10 screws; the other two screws are Torx T15 screws. Be sure to install these screws in the correct locations when reinstalling the MultiBay. 8. Slide the MultiBay forward and then left it out of the base cover . Figure 5-25 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 56
5.12 Control Panel 1. Prepare the expansion base for disassembly (Section 5.3). 2. Remove the tray (Section 5.4). 3. Remove the connector cover (Section 5.5). 4. Remove the rear bezel (Section 5.6). 5. Remove the top cover (Section 5.8). 6. Remove the MultiBay (Section 5.11). 7. Disconnect the right - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 57
5.13 Mechanism Assembly IMPORTANT: The mechanism assembly contains white lithium grease, which is used as a lubricant. The mechanism assembly is spared as a unit and should not be disassembled. 1. Prepare the expansion base for disassembly (Section 5.3). 2. - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 58
assembly cover and pulling the assembly out of the backplane (Figure 5-28). Figure 5-28. Removing the Mechanism Assembly Reverse the removal procedure described above to install the mechanism assembly. 5-28 Removal and Replacement Procedures - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 59
5.14 Power Supply CAUTION: Do not handle or carry the power supply by the wiring harness. This can cause damage to the power supply and wiring harness. 1. Prepare the expansion base for disassembly (Section 5.3). 2. Remove the tray (Section 5.4). 3. Remove the rear bezel (Section 5.6). 4. Remove the - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 60
7. If a half-height device is installed in the half-height bay, disconnect the half height bay power supply cable from the half-height supply. Figure 5-30. Removing the Power Supply Reverse the removal procedure described above to install the power supply. 5-30 Removal and Replacement Procedures - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 61
Backplane 1. Prepare the expansion base for disassembly (Section 5.3). 2. Remove the tray (Section 5.4). 3. Remove the rear bezel (Section 5.6). 4. If installed, remove any PCI expansion boards (Section 5.7). 5. Remove the top cover (Section 5.8). 6. Remove the MultiBay (Section 5.11). 7. Remove the - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 62
Expansion Base Physical and Environmental Specifications U.S. Metric Dimensions Height with monitor support cover Without monitor support cover Depth with monitor support cover Without monitor support cover Width Weight with monitor support cover without monitor support cover Power Supply (Input - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 63
The Expansion Base is designed in accordance with ANSI specifications (no. X3.131-1993, Rev 10h) and IEEE 802.3 specifications. NOTE: This product is designed for IT power systems with phase-to-phase voltage not exceeding 240Vrms minimum charge. 6-2 Specifications - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 64
A appendix CONNECTOR PIN ASSIGNMENTS This appendix contains the pin assignments for all external connectors. Connector 12 Table A-1 Headphone Jack Pin Signal 1 Audio out 2 Ground Connector 12 Table A-2 Microphone Jack Pin Signal 1 Audio in 2 Ground Connector Pin Assignments A-1 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 65
Table A-3 Parallel Connector 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 14 Pin Signal 1 Strobe 2 Data Bit 0 3 Data Bit 1 4 Data Bit 2 5 Data Bit 3 6 Data Bit 4 7 Data Bit 5 8 Data Bit 6 9 Data Bit 7 10 Acknowledge 11 Busy 12 Paper End 13 Select Connector 6 5 4 KEY 3 21 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 66
Pin Signal 1 Red Analog 2 Green Analog 3 Blue Analog 4 Monitor ID Bit 2 5 Ground 6 Ground 7 Ground 8 Ground Connector 12 Connector 12 Table A-6 External Monitor Connector 5 43 21 10 KEY 8 7 6 15 14 13 12 11 Pin Signal 9 +5 Volt Supply 10 Ground 11 Monitor ID Bit 0 12 Monitor ID - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 67
Pin Signal 1 EBOXL 2 AGND 3 EBOXS1 4 RED 5 AGND 6 GREEN 7 AGRD 8 BLUE 9 AGND 10 VSYNC 11 HSYNC 12 DDC DAT 13 DDC CLK 14 GND 15 INDEX 16 RDATA 17 TRK0 18 WDATA 19 WGATE 20 STEP 21 DIR 22 POWER ON 23 SYS RESET 24 GND 25 DSKCHG 26 +5 V (VDD) 27 AUGND 28 XA2/L IN 29 XA3/R IN 30 MID0/MIC IN 31 AUGND 32 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 68
Table A-13 Continued Pin Signal 67 PDATA6 LD14 68 PDATA7 LD15 69 GND 70 ERROR LCLK 71 RXD1 LVREQ 72 TXD1 LCREQ 73 RTS1 LEN 74 GND 75 CTS1 LIIC CLK 76 DTR1 LIIC DAT 77 DSR1 EX 78 DCD1 EX 79 12C DATA 80 GND 81 12C CLK 82 GND 83 HDSEL 84 GND 85 WPROT 86 EBOXS2 /GND 87 ERDY 88 EBOXL /GND 89 FLUSHREQ 90 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 69
Table A-13 Continued Pin Signal 143 VBATT 144 AD[23] 145 GND 146 AD[21] 147 AD[19] 148 AD[17] 149 GND 150 AD[14] 151 AD[12] 152 AD[10] 153 AD[08] 154 GND 155 AD[07] 156 AD[05] 157 AD[03] 158 AD[01] 159 GND Pin Signal 160 CBE3 161 CBE2 162 IRDY 163 DEVSEL 164 LOCK 165 OERR 166 SERR 167 GND 168 RSVD3 - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 70
other countries must meet the requirements of the country where the ArmadaStation and Armada MiniStation are used. For more information on power cord set requirements, contact a Compaq authorized reseller or service provider. General Requirements The requirements listed below are applicable to all - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 71
Country-Specific Requirements 3-Conductor Power Cord Set Requirements-By Country Country Accredited Agency Applicable Note Numbers Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 72
, 1-1 feet installing, 5-4 G generating static, 4-2 grounding equipment, 4-4 methods, 4-3 workstations, 4-4 H half-height bay illustrated, 1-3 bays, 1-7, 5-14 hard drive cable connecting, 5-20 illustrated, 3-2, 3-5 headphone jack illustrated, 1-4 pinout, A-1 height specification, 6-1 humidity - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 73
microphone jack illustrated, 1-4 pinout, A-1 Miscellaneous Cable Kit cable illustrated, 3-2 monitor carbon spare part number, 3-6 connector illustrated, 1-5 pinout, 1-3 latch slot illustrated, 1-5 monitor support cover recess illustrated, 1-3 monitor support cover specification, 6-1 mouse connector - Compaq Armada e500s | Compaq ArmadaStation EM Maintenance and Service Guide - Page 74
, v temperature specification, 6-1 tools required for service, 4-6 top cover illustrated, 3-2 removing, 5-12 spare part number, 3-3 tower stand spare part number, 3-6 tray assembly illustrated, 3-2 removing, 5-5 spare part number, 3-3 troubleshooting, 2-1 U U-bolt illustrated, A-5 USB connectors
Compaq ArmadaStation EM
Maintenance and Service Guide