Craftsman 28907 Operation Manual - Page 26

Replacing, Battery, To Adjust, Throttle, Control

Get Craftsman 28907 - Lt 2000 19.5 HP/42inch Lawn Tractor PDF manuals and user guides View all Craftsman 28907 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

REPLACING BATTERY TO REPLACE FUSE _ WARNING" • Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. 1. Lift seat pan to raised position. 2. Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor. 3. Install new battery with terminals in same position as old battery. 4. First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal 5. Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely. Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. TO REMOVE HOOD & GRILLASSEMBLY 1. Raise hood. 2. Unsnap headlight wire connector. 3. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. 4. When replacing hood, be sure to reconnect the headlight wire connector. Headlight Wire Connector Seat Pan Terminal Cover Keps Nut ""_(4'- Hex Bolt ENGINE TO ADJUST THROTTLE CONTROL The throttle control has been preset at the factory and adjustment should not be necessary Check adjustment as described below before loosening cable. If adjustment is necessary, see engtne manual. TO ADJUST CHOKE CONTROL The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual. TO ADJUST CARBURETOR Positive (Red) Cable Negati\ (Black) Cable TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Remove bulb holder from the hole in the backside of the grill. 3. Replace bulb in holder and install bulb holder securely back into the hole in the backside of the grill. 4. Close hood. INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Repair Parts manual. Your carburetor has been preset atthe factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the engine does need adjustment, see engine manual. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
REPLACING
BATTERY
_
•
WARNING"
Do not short battery ter-
minals by allowing
a wrench
or any other
object to contact
both terminals
at the
same time. Before connecting
battery, re-
move metal bracelets,
wristwatch
bands,
rings, etc.
Positive terminal
must be connected
first to prevent sparking from accidental
grounding.
1.
Lift seat pan to raised position.
2.
Disconnect
BLACK battery cable first
then RED battery cable and carefully
remove
battery from tractor.
3.
Install new battery with terminals
in
same position as old battery.
4.
First connect
RED battery cable to
positive
(+) terminal
with hex bolt and
keps nut as shown. Tighten
securely.
Slide terminal
cover over terminal
5.
Connect
BLACK grounding
cable
to negative
(-) terminal with remain-
ing hex bolt and keps nut. Tighten
securely.
Seat Pan
Terminal Cover
Keps Nut
""_(4'-
Hex Bolt
Positive
(Red)
Negati\
(Black)
Cable
Cable
TO REPLACE
HEADLIGHT
BULB
1.
Raise hood.
2.
Remove
bulb holder from the hole in
the backside
of the grill.
3.
Replace
bulb in holder and install bulb
holder securely
back into the hole in
the backside
of the grill.
4.
Close hood.
INTERLOCKS
AND
RELAYS
Loose or damaged
wiring may cause
your tractor to run poorly, stop running,
or
prevent it from starting.
•
Check wiring.
See electrical
wiring
diagram
in the Repair Parts manual.
TO
REPLACE
FUSE
Replace with 20 amp automotive-type
plug-in fuse.
The fuse holder
is
located
behind the dash.
TO
REMOVE
HOOD & GRILLASSEMBLY
1.
Raise hood.
2.
Unsnap
headlight wire connector.
3.
Stand in front of tractor.
Grasp hood at
sides, tilt toward
engine and lift off of
tractor.
4.
When
replacing
hood, be sure to re-
connect
the headlight
wire connector.
Headlight
Wire
Connector
ENGINE
TO ADJUST
THROTTLE
CONTROL
The
throttle
control
has
been
preset
at
the factory
and adjustment
should
not
be
necessary
Check adjustment
as described
below before loosening cable. If adjustment
is necessary,
see engtne manual.
TO ADJUST
CHOKE
CONTROL
The choke
control
has been
preset at the
factory and adjustment
should not be neces-
sary. If adjustment
is necessary, see
engine
manual.
TO ADJUST
CARBURETOR
Your carburetor has been preset atthe factory
and adjustment
should
not be necessary.
However, minor adjustment
may be required
to compensate
for differences
in
fuel, tem-
perature, altitude or load.
If
the engine does
need adjustment,
see engine
manual.
26